download in here
Minggu, 15 November 2009
HP Restart Dan Hang solusi awalnya....disini
P3(PertolonganPertamaPada) HP Restart Dan Hang
a. Coba format manual HP ( restore factory setting )
Untuk ponsel NOKIA dengan tipe, 7650,3650/60,6600, N Gage :
>> Tekan *, kemudian, yes, lalu 3, secara bersamaan sambil menekan tombol power on/off e.
>> Format langsung melalui ponsel dengan menekan *#7370# >>12345
Untuk ponsel NOKIA dengan tipe, 9110, 9210 :
>> Format langsung melalui ponsel dengan menekan Shift + Tab + F ketika baterai dipasang...trus..salaman..
Untuk ponsel NOKIA dengan tipe, 9300,9500 :
>> Format langsung melalui ponsel dengan menekan Ctrl + Shift + F ketika baterai dipasang....trus ..salaman..
Untuk ponsel NOKIA dengan tipe, 3585/6, 2280, 2115/6 , 3105
>> Format langsung melalui ponsel dengan menekan *#75681#
b. Bila langkah diatas gagal, coba lakukan flashing sesuai tipenya.
jika kasus tetap semua kemungkinan kerusakan pada hardwarenya .
a. Coba format manual HP ( restore factory setting )
Untuk ponsel NOKIA dengan tipe, 7650,3650/60,6600, N Gage :
>> Tekan *, kemudian, yes, lalu 3, secara bersamaan sambil menekan tombol power on/off e.
>> Format langsung melalui ponsel dengan menekan *#7370# >>12345
Untuk ponsel NOKIA dengan tipe, 9110, 9210 :
>> Format langsung melalui ponsel dengan menekan Shift + Tab + F ketika baterai dipasang...trus..salaman..
Untuk ponsel NOKIA dengan tipe, 9300,9500 :
>> Format langsung melalui ponsel dengan menekan Ctrl + Shift + F ketika baterai dipasang....trus ..salaman..
Untuk ponsel NOKIA dengan tipe, 3585/6, 2280, 2115/6 , 3105
>> Format langsung melalui ponsel dengan menekan *#75681#
b. Bila langkah diatas gagal, coba lakukan flashing sesuai tipenya.
jika kasus tetap semua kemungkinan kerusakan pada hardwarenya .
tips n trik CNT fail
trik extracting content pack failed pada 1200,1209&1650
seperti yg kita tau klo CNT (content packs) tidak masuk saat proses flashing
hp akan menjadi matot ato contact servis.
mungkin dengan sedikit trik ini hp akan dapat membantu teman2 tanpa harus bermain hardware.
trik ini sudah saya test pada beberapa hp dengan kasus yg sama dan hasilnya sukses,
tapi dengan syarat kita harus mempunyai mxkey+UFS hwk.
- lakukan proses flashing seperti biasa menggunakan mxkey
- saat proses extrcting cnt failed proses flashing akan berhenti dan muncul tab dengan pilihan ok/cancel
- jangan pilih cancel,cabut kabel flash dari hp dan tempelin pin baterai (pin flash jangan nempel)
- tekan power on sampai muncul "test mode" pada layar hp
- klik "ok' pada tab pilihan
- extracting CNT masuk deh.........
kalaupun terlanjur full erase masih bia dengan cara di atas,cuma pada saat write PM lebih mudah menggunakan UFS+HWK
caranya :
- setelah flashing dengan mxkey (cara di atas)
- pilih check pada hwk suite
- lalu klik info....nah kalo info ga muncul pake trik "test mode" seperti diatas
- kalo info dah muncul baru write PM....(kalo gagal ulangi dari klik info ya)
- nah kalo sukses PM pasti masuk....
sekarang tinggal repair simlock
untuk cara ini lebih baik gunakan mxkey karena lebih mudah
- boleh pake bus check pada mxkey boleh juga tidak
- klo sudah yakin hp konek masuk langsung aja masuk pada simlock info
- info simlock ga akan langsung keluar,jadi pake lagi "trik test mode"
- kalo info simlock dah muncul baru pilih update simlock
- tunggu proses patching berjalan....saat proses patching selasai buru2 cabut kabel dan gunain "trik test mode"
- maksudnya biar simlock bisa di repair pada kondisi hp test mode
- klo sukses simlock akan terbuka semua
selamat mencoba
nb:trik ini agak susah karena harus cabut pasang kabel flash...jadi berusaha ya jangan menyerah
maaf kalo kurang jelas...ga biasa nulis menulis sih hehehehehhehe ......
seperti yg kita tau klo CNT (content packs) tidak masuk saat proses flashing
hp akan menjadi matot ato contact servis.
mungkin dengan sedikit trik ini hp akan dapat membantu teman2 tanpa harus bermain hardware.
trik ini sudah saya test pada beberapa hp dengan kasus yg sama dan hasilnya sukses,
tapi dengan syarat kita harus mempunyai mxkey+UFS hwk.
- lakukan proses flashing seperti biasa menggunakan mxkey
- saat proses extrcting cnt failed proses flashing akan berhenti dan muncul tab dengan pilihan ok/cancel
- jangan pilih cancel,cabut kabel flash dari hp dan tempelin pin baterai (pin flash jangan nempel)
- tekan power on sampai muncul "test mode" pada layar hp
- klik "ok' pada tab pilihan
- extracting CNT masuk deh.........
kalaupun terlanjur full erase masih bia dengan cara di atas,cuma pada saat write PM lebih mudah menggunakan UFS+HWK
caranya :
- setelah flashing dengan mxkey (cara di atas)
- pilih check pada hwk suite
- lalu klik info....nah kalo info ga muncul pake trik "test mode" seperti diatas
- kalo info dah muncul baru write PM....(kalo gagal ulangi dari klik info ya)
- nah kalo sukses PM pasti masuk....
sekarang tinggal repair simlock
untuk cara ini lebih baik gunakan mxkey karena lebih mudah
- boleh pake bus check pada mxkey boleh juga tidak
- klo sudah yakin hp konek masuk langsung aja masuk pada simlock info
- info simlock ga akan langsung keluar,jadi pake lagi "trik test mode"
- kalo info simlock dah muncul baru pilih update simlock
- tunggu proses patching berjalan....saat proses patching selasai buru2 cabut kabel dan gunain "trik test mode"
- maksudnya biar simlock bisa di repair pada kondisi hp test mode
- klo sukses simlock akan terbuka semua
selamat mencoba
nb:trik ini agak susah karena harus cabut pasang kabel flash...jadi berusaha ya jangan menyerah
maaf kalo kurang jelas...ga biasa nulis menulis sih hehehehehhehe ......
kode rahasia hp china
Kode rahasia handphone china
Service codes "Chinese" models:
* default user code: 1122, 3344, 1234, 5678
* Engineer mode: *#110*01#
* Factory mode: *#987#
* Enable test mode COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
* Restore factory settings: *#987*99#
* LCD contrast: *#369#
* software version: *#800#
* software version: *#900#
*#66*# Set Factory Mode CONFIRMED
*#8375# Show Software Version CONFIRMED
*#1234# A2DP ACP Mode CONFIRMED
*#1234# A2DP INT Mode CONFIRMED
*#0000# + Send : Set Default Language CONFIRMED
*#0007# + Send : Set Language to Russian CONFIRMED
*#0033# + Send : Set Language to French CONFIRMED
*#0034# + Send : Set Language to Spanish CONFIRMED
*#0039# + Send : Set Language to Italian CONFIRMED
*#0044# + Send : Set Language to English CONFIRMED
*#0049# + Send : Set Language to German CONFIRMED
*#0066# + Send : Set Language to Thai CONFIRMED
*#0084# + Send : Set Language to Vietnamese CONFIRMED
*#0966# + Send : Set Language to Arabic CONFIRMED
More some codes for reset mobile china
*#77218114#
*#881188#
*#94267357#
*#9426*357#
*#19912006#
*#118811#
*#3646633#
CHINESE MODELS:
default user code: 1122, 3344, 1234, 5678
Engineer mode: *#110*01#
Factory mode: *#987#
Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
Restore factory settings: *#987*99#
LCD contrast: *#369#
software version: *#800#
software version: *#900#
set default language: *#0000# Send
set English language: *#0044# Send
set English language (new firmware): *#001# Send
also
==========
Service codes BenQ:
software version: *#300#
test mode: *#302*20040615#
Service codes Pantech:
software version: *01763*79837#
service menu: *01763*476#
reset defaults (phone/user code reset to default): *01763*737381#
Service codes 3xx, 5xx:
software version: *#79#
software version: *#837#
Service codes VK200, VK2000, VK2010, VK2020, VK4000:
software version: *#79#
service menu: *#9998*8336# (hold #)
reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
Service codes LG:
software version: 2945#*#
Service codes Sony-Ericsson:
J100 software version: #82#
Service codes Fly:
2040(i) reset defaults: *#987*99# Send
MX200 reset defaults: *#987*99# Send
MX200 software version: *#900# Send
SL300m reset defaults: *#987*99# Send
SL300m software version: *#900# Send
SL500m reset defaults: *#987*99# Send
SL500m software version: *#900# Send
MP500 reset defaults: *#987*99# Send
MP500 software version: *#900# Send
Set language to English: *#0044#
Set language to Russian: *#0007#
Service codes Konka:
C926 software version: *320# Send
C926 set default language: *#0000# Send
C926 set English language: *#0044# Send
Service codes GStar:
GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
Set language to English: *#0044#
Set language to Russian: *#0007#
ZTE Mobile1- *938*737381#
2- PHONE WILL DIPLAYED DONE
3- POWER OFF YOUR PHONE AND POWER ON AGAIN
alcatelE205
unlocking phone code,only press***847# without simcard
E900 software version: *#5002*8376263#
E900 full reset: *2767*3855#
Service codes Spice:
S404 enable COM port: *#42253646633# -> Device -> Set UART -> PS -> UART1/115200
S410 engineer mode: *#3646633#
S900 software version: *#8375#
S900 serial no: *#33778#
Service codes Philips:
S200 enable COM port: *#3338913# -> Device -> Set UART -> PS -> UART1/115200
Service codes "Chinese" models:
default user code: 1122, 3344, 1234, 5678
Engineer mode: *#110*01#
Factory mode: *#987#
Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
Restore factory settings: *#987*99#
LCD contrast: *#369#
software version: *#800#
software version: *#900#
Service codes BenQ:
software version: *#300#
test mode: *#302*20040615#
Service codes Pantech:
software version: *01763*79837#
service menu: *01763*476#
reset defaults (phone/user code reset to default): *01763*737381#
Service codes VK-Mobile 3xx, 5xx:
software version: *#79#
software version: *#837#
service menu: *#85*364# (hold #)
Service codes VK200, VK2000, VK2010, VK2020, VK4000:
software version: *#79#
service menu: *#9998*8336# (hold #)
reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
Service codes LG:
software version: 2945#*#
KG300 NVRAM format: 2945#*# -> menu 15
Service codes Sony-Ericsson:
J100 software version: #82#
Service codes Fly:
M100 software version: ####0000#
2040(i) reset defaults: *#987*99# Send
MX200 reset defaults: *#987*99# Send
MX200 software version: *#900# Send
SL300m reset defaults: *#987*99# Send
SL300m software version: *#900# Send
SL500m reset defaults: *#987*99# Send
SL500m software version: *#900# Send
MP500 reset defaults: *#987*99# Send
MP500 software version: *#900# Send
Set language to English: *#0044#
Set language to Russian: *#0007#
Service codes Konka:
C926 software version: *320# Send
C926 set default language: *#0000# Send
C926 set English language: *#0044# Send
Service codes GStar:
GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
Set language to English: *#0044#
Set language to Russian: *#0007#
Service codes Motofone-F3:
Motofone F3 software version: **9999* Send
***300* Set SIM Pin
***310* / ***311* SIM Pin ON | OFF
***000* Reset Factory settings
***644* Set Voicemail number
***260* / ***261* Auto keypad lock ON | OFF
***510* / ***511* Voice Prompts ON | OFF
***160* / ***161* Restricted Calling (Phonebook only) ON | OFF
***200608* Send: software version
***200606* Send: software version
***200806* Send: flex version
***250* / ***251* Keypad tones ON | OFF
***470* Select time format
***500* /***501* Prepaid Balance Display ON | OFF
***520* Change language
Service codes Motorola:
C113, C114, C115, C115i, C116, C117, C118 software version: #02#*
C138, C139, C140 software version: #02#*
C155, C156, C157 software version: #02#*
C257, C261 software version: #02#*
V171, V172, V173 software version: #02#*
V175, V176, V176 software version: #02#*
C168, W220 software version: *#**837#
W208, W375 software version: #02#*
and "yes"''
-mobile Inno30, 55, 89, 90, 99, 100, A10, A20, P10, Vk200
- Set full factory *741*737381#
- Set full factory *741*7373868#
- Set full factory *741*2878#
- Set Engineer Mode *888*888#
- Check software version *888*837#
I-mobile 100 ,200 , 313
- Check software version #*888#
I-mobile 309, 310
- Check software version *0*4636#
- Test Mode *0*6268#
I-mobile 311
- Check software version #*878#
I-mobile 511
- Check software version *1222*1#
I-mobile 301, 302,308, 508, 601, 602, 603, 604, 606, 611, 901, 902
- Check software version *#159#
- Set Factory Mode *#32787#
- Set Engineer Mode *#3646633#
I-mobile 503, 506, 605, 600, 607, 608
- Set Engineer Mode ***503#
- Set Factory Mode ***504#
- Set Auto Test ***505#
I-mobile 509, 612
- Set Factory Mode *#66*#
I-mobile 504, 505, 803
- Check software version *68*48#
- Set full factory *789#
- Test Mode *#789#
I-mobile 305, 306, 315, 510, 609, 609i,516
- Check software version *#8375#
- Set Factory Mode 878
I-mobile 610
- Check software version *#22#
I-mobile J101, J102
- Test Mode *23638777*783781#
I-mobile 502, 502i, 505, k9, 802
- Check software version *201206*4636#
selamat mencoba
sukses terus para teknisi indonesia khususnya surabaya
* default user code: 1122, 3344, 1234, 5678
* Engineer mode: *#110*01#
* Factory mode: *#987#
* Enable test mode COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
* Restore factory settings: *#987*99#
* LCD contrast: *#369#
* software version: *#800#
* software version: *#900#
*#66*# Set Factory Mode CONFIRMED
*#8375# Show Software Version CONFIRMED
*#1234# A2DP ACP Mode CONFIRMED
*#1234# A2DP INT Mode CONFIRMED
*#0000# + Send : Set Default Language CONFIRMED
*#0007# + Send : Set Language to Russian CONFIRMED
*#0033# + Send : Set Language to French CONFIRMED
*#0034# + Send : Set Language to Spanish CONFIRMED
*#0039# + Send : Set Language to Italian CONFIRMED
*#0044# + Send : Set Language to English CONFIRMED
*#0049# + Send : Set Language to German CONFIRMED
*#0066# + Send : Set Language to Thai CONFIRMED
*#0084# + Send : Set Language to Vietnamese CONFIRMED
*#0966# + Send : Set Language to Arabic CONFIRMED
More some codes for reset mobile china
*#77218114#
*#881188#
*#94267357#
*#9426*357#
*#19912006#
*#118811#
*#3646633#
CHINESE MODELS:
default user code: 1122, 3344, 1234, 5678
Engineer mode: *#110*01#
Factory mode: *#987#
Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
Restore factory settings: *#987*99#
LCD contrast: *#369#
software version: *#800#
software version: *#900#
set default language: *#0000# Send
set English language: *#0044# Send
set English language (new firmware): *#001# Send
also
==========
Service codes BenQ:
software version: *#300#
test mode: *#302*20040615#
Service codes Pantech:
software version: *01763*79837#
service menu: *01763*476#
reset defaults (phone/user code reset to default): *01763*737381#
Service codes 3xx, 5xx:
software version: *#79#
software version: *#837#
Service codes VK200, VK2000, VK2010, VK2020, VK4000:
software version: *#79#
service menu: *#9998*8336# (hold #)
reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
Service codes LG:
software version: 2945#*#
Service codes Sony-Ericsson:
J100 software version: #82#
Service codes Fly:
2040(i) reset defaults: *#987*99# Send
MX200 reset defaults: *#987*99# Send
MX200 software version: *#900# Send
SL300m reset defaults: *#987*99# Send
SL300m software version: *#900# Send
SL500m reset defaults: *#987*99# Send
SL500m software version: *#900# Send
MP500 reset defaults: *#987*99# Send
MP500 software version: *#900# Send
Set language to English: *#0044#
Set language to Russian: *#0007#
Service codes Konka:
C926 software version: *320# Send
C926 set default language: *#0000# Send
C926 set English language: *#0044# Send
Service codes GStar:
GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
Set language to English: *#0044#
Set language to Russian: *#0007#
ZTE Mobile1- *938*737381#
2- PHONE WILL DIPLAYED DONE
3- POWER OFF YOUR PHONE AND POWER ON AGAIN
alcatelE205
unlocking phone code,only press***847# without simcard
E900 software version: *#5002*8376263#
E900 full reset: *2767*3855#
Service codes Spice:
S404 enable COM port: *#42253646633# -> Device -> Set UART -> PS -> UART1/115200
S410 engineer mode: *#3646633#
S900 software version: *#8375#
S900 serial no: *#33778#
Service codes Philips:
S200 enable COM port: *#3338913# -> Device -> Set UART -> PS -> UART1/115200
Service codes "Chinese" models:
default user code: 1122, 3344, 1234, 5678
Engineer mode: *#110*01#
Factory mode: *#987#
Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
Restore factory settings: *#987*99#
LCD contrast: *#369#
software version: *#800#
software version: *#900#
Service codes BenQ:
software version: *#300#
test mode: *#302*20040615#
Service codes Pantech:
software version: *01763*79837#
service menu: *01763*476#
reset defaults (phone/user code reset to default): *01763*737381#
Service codes VK-Mobile 3xx, 5xx:
software version: *#79#
software version: *#837#
service menu: *#85*364# (hold #)
Service codes VK200, VK2000, VK2010, VK2020, VK4000:
software version: *#79#
service menu: *#9998*8336# (hold #)
reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
Service codes LG:
software version: 2945#*#
KG300 NVRAM format: 2945#*# -> menu 15
Service codes Sony-Ericsson:
J100 software version: #82#
Service codes Fly:
M100 software version: ####0000#
2040(i) reset defaults: *#987*99# Send
MX200 reset defaults: *#987*99# Send
MX200 software version: *#900# Send
SL300m reset defaults: *#987*99# Send
SL300m software version: *#900# Send
SL500m reset defaults: *#987*99# Send
SL500m software version: *#900# Send
MP500 reset defaults: *#987*99# Send
MP500 software version: *#900# Send
Set language to English: *#0044#
Set language to Russian: *#0007#
Service codes Konka:
C926 software version: *320# Send
C926 set default language: *#0000# Send
C926 set English language: *#0044# Send
Service codes GStar:
GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
Set language to English: *#0044#
Set language to Russian: *#0007#
Service codes Motofone-F3:
Motofone F3 software version: **9999* Send
***300* Set SIM Pin
***310* / ***311* SIM Pin ON | OFF
***000* Reset Factory settings
***644* Set Voicemail number
***260* / ***261* Auto keypad lock ON | OFF
***510* / ***511* Voice Prompts ON | OFF
***160* / ***161* Restricted Calling (Phonebook only) ON | OFF
***200608* Send: software version
***200606* Send: software version
***200806* Send: flex version
***250* / ***251* Keypad tones ON | OFF
***470* Select time format
***500* /***501* Prepaid Balance Display ON | OFF
***520* Change language
Service codes Motorola:
C113, C114, C115, C115i, C116, C117, C118 software version: #02#*
C138, C139, C140 software version: #02#*
C155, C156, C157 software version: #02#*
C257, C261 software version: #02#*
V171, V172, V173 software version: #02#*
V175, V176, V176 software version: #02#*
C168, W220 software version: *#**837#
W208, W375 software version: #02#*
and "yes"''
-mobile Inno30, 55, 89, 90, 99, 100, A10, A20, P10, Vk200
- Set full factory *741*737381#
- Set full factory *741*7373868#
- Set full factory *741*2878#
- Set Engineer Mode *888*888#
- Check software version *888*837#
I-mobile 100 ,200 , 313
- Check software version #*888#
I-mobile 309, 310
- Check software version *0*4636#
- Test Mode *0*6268#
I-mobile 311
- Check software version #*878#
I-mobile 511
- Check software version *1222*1#
I-mobile 301, 302,308, 508, 601, 602, 603, 604, 606, 611, 901, 902
- Check software version *#159#
- Set Factory Mode *#32787#
- Set Engineer Mode *#3646633#
I-mobile 503, 506, 605, 600, 607, 608
- Set Engineer Mode ***503#
- Set Factory Mode ***504#
- Set Auto Test ***505#
I-mobile 509, 612
- Set Factory Mode *#66*#
I-mobile 504, 505, 803
- Check software version *68*48#
- Set full factory *789#
- Test Mode *#789#
I-mobile 305, 306, 315, 510, 609, 609i,516
- Check software version *#8375#
- Set Factory Mode 878
I-mobile 610
- Check software version *#22#
I-mobile J101, J102
- Test Mode *23638777*783781#
I-mobile 502, 502i, 505, k9, 802
- Check software version *201206*4636#
selamat mencoba
sukses terus para teknisi indonesia khususnya surabaya
Kamis, 22 Oktober 2009
5220 conser tanpa RPL
Langkah-langkah repair 5220 conser tanpa menggunakan RPL
1.Cek versi hp dulu
2.Backup full pm dan rpl mengunakan mxkey
3.Erase menggunakan mxkey dengan menggunakan menu get address
4.Flash dengan menggunakan firmware rm-303 v.7,hanya file MCU dan PPM aja
5.Hp harus local mode dengan imei 123456….dan jika tidak local mode gunakan menu reset NPC supaya hp jadi local mode
6.Masukan backup an pm (masukin PM menggunakan ufs hwk 2.09 karena ada sx4 bypass)7.Masukan backup an RPL menggunakan mxkey
8.Lihat status simlocknya menggunakan buschek pada mxkey
9.Status harus valid dan pass semua kecuali superdongle
10.Backup kembali full pm dan RPL nya
11.Flashing kembali menggunakan firmware rm-411 v.4.86, hanya MCU dan PPM aja
12.Lihat status simlocknya pake buschek,keadaan harus masih valid dan pass kecuali superdongle
13.Kalau status berubah invalid pada simlock, masukan backup rpl yang ke 2
14.Buscheck lagi untuk melihat status simlocknya, status simlock harus valid dan pass kecuali superdongle
15.Flashing dengan firmware rm-411 v.6.51 ato firmware aslinya, fullflash
16.Buscheck lagi, status harus valid dan pass semua.
17.Lihat hasilnya, hp normal tidak lagi contact service
18.Bikin nota…..
Catatan..
-Jika gagal proses di ulangi lagi,harus selalu lihat status simlocknya setelah kita melakukan setiap langkah
-Pm tidak usah di edit-Pada intinya kita mensiasati security yang diprotek, dengan flashing firmware/type hp yang tidak terproteksi kemudian kita ambil datanya
-Ini langkah2 yang saya lakukan
-Kreatifitas dan kecerdikan serta kejelian-Mungkin ada langkah2 yang keliru atopun salah…mohon dikoreksi para master…ini hanya salah satu solusi..semoga bermanfaat
-SELAMAT BERJUANG SEMOGA BERHASIL
Rabu, 14 Oktober 2009
Senin, 12 Oktober 2009
update jaf 1.98.64
JAF exe 1.98.64 ready
- improved N97 flashing
- added sx4 bypass
- added support for Vista SP2
- added check for JAF.exe file location
- small bugs fixed
sedot dong mang
- improved N97 flashing
- added sx4 bypass
- added support for Vista SP2
- added check for JAF.exe file location
- small bugs fixed
sedot dong mang
All nokia hard library v7.00 HOT
------------------------------------------------------------------
Interface more powerfull and easy to use.- Easy to update in future ( no need to download full package).
- More models and solutions are added.
. Models and Solutions
1100/2300: car,charge,earpiece,speaker,local mode,micro,network,on/off,ring,sim
1110/1600/2310: buzzer,charge,handsfree,keypad,lcd,lcd light,light,sim,test mode
1200: charge,keypad,lcd,light,micro,on/off,sim,speaker,test mode
1650: dislay light,on/off,ring,test mode
2600: buzzer,car,charge,lcd,light,test mode
2610: audio,car,charge,lcd,micro,test mode
2630: charge,on/off,test mode
2650: car,display,headset,light,micro,ring,sim
2660: light,sim
2760: charge,sim
3100: antenna,blue lcd,charge,lcd,lcd light,local mode,on/off,ring,sim,sim track
3110: charge,display,display2,ear,speaker,keypad,light,m icro,mmc,on/off,sim,spaeker
3200: camera,charge,display,keypad,lcd,light,local mode,on/off,ring,sim
3220/6020: camera,charge,headset,keypad,lcd,led,local mode,micro,on/off,sim
3230: audio,camera,ear,hang,headset,joystick,keypad,lcd, lcd light,led,mmc,on/off,spaeker
3250: bt,camera,charge,display,earpiece,keypad,lcd,micro ,mmc,on/off,signal,sim
3650: blank,camera,display,headset,keypad,lcd,led,micro, mmc,on/off,sim,speaker,vibra,white
5100: lcd,sim
5140: camera,lcd,
5200/5300: buzzer,camera,charge,display,keypad,lcd light,light,micro,mmc,network,on/off,sim
5310: buzzer,camera,charge,display,earpiece,flex,full,ke ypad,lcd,micro,mmc,network,on/off,sim
5500: audio,display,keypad,network,ring,sim,speaker
5610: micro,on/off
5700: buzzer,micro
6030: keypad,lcd,lcd light,micro,buzzer,charge,test mode,lcd,lcd light,sim
6060: charge,local mode,sim
6070: buzzer,camera,charge,keypad,lcd,lcd light,local mode,on/off,sim,speaker
6085: handsfree,micro,sim
6101: buzzer,lcd light,light,local mode,sim
6110: micro
6120: buzzer,keypad,lcd,light,vibra,vol keys
6125: charge,keypad,camera,micro,sim
6131: blank,charge,keypad,led,micro,mmc,on/off
6151: sim
6170: down keys,keypad,local mode
6230: buzzer,camera,charge,gallery,keypad,led,light,mmc, on/off,sim,test mode,vol keys
6233: audio,bt,bsi,camera,charge,display,ear,keypad,lcd, led,micro,mmc,network,ring,sim,slide keys,vol keys
6260: charge,keypad,lcd,light,micro,mmc,on/off,ring,sim
6263: buzzer,keypad
6267: buzzer,charge,on/off,vibra,camera
6270: camera,charge,display,headset,keypad,led,light,mic ro,network
6280: blank,bt,camera,charge,display,keypad,lcd led,mmc,on/off,signal,sim
6300: blue lcd,bt,camera,charge,display,keypad,lcd,lcd light,led,micro,mmc,network,not power,on/off,ring,sim,spaeker,vibra
6500c: charge
6500s: camera
6600: batt,blank,buzzer,camera,charge,display,earpiece,g allery,joystick,keyboard,keypad,lcd led,micro,mmc,network,on/off,sim,spaker,vibra
6610/7210: lcd,light,not power,on/off,ring,sim
6630: audio,bt,camera,charge,display,earpiece,headset,ke ypad,light,mico,not power,on/off,sim,speaker,vibra,white
6670/7610: camera,charge,display,ear,keyboard,lcd,micro,on/off,ring,sim
6680: bt,camera,display,handfree,keypad,light,mmc,networ k,on/off,signal,sim,white
7200: led,local mode,sim
7250: micro,lcd,not power,light
7360: headset,keys,light,sim,speaker
7370: charge,keypad,local mode,vol keys
7373: mmc,sim
7390: charge
7500: camera,charge
7710: blank,display,mmc
8800: light,sim
E50 : audio,charge,joystick,keypad,micro,mmc
E60 : bt,buzzer,charge,display,keypad,light,on/off,sim,speaker,vibra,white
E61 : audio,blank,charge,joystick,lcd,on/off,signal,sim
E65 : display,keypad,lcd,light,offline,white
N70 : Audio,bt,camera,charge,ear,flash light,handfree,keypad,lcd,light,micro,missmatch,mm c,on/off,ring,signal,sim,synchro,white
N73 : charge,front cam,joystick,keypad,led,micro,ear,mmc,network,on/off,sim,speaker,vibra,white
N80 : charge,hang,keypad,lcd,light,mmc,network,on/off,ring,svc,white
N81 : boot,camera
N90 : charge,keypad,micro,network,sim
N91 : charge,display,ear,handfree,hang,hdd,keypad,on/off,vibra,white
N93 : charge,keypad,micro,offline
N95 : audio,bluelcd,bt,cam keys,camera,charge,flash cam,keypad,lcd,lcd led,lightmmc,network,on/off,restart,sim,usb,vibra
download here
Interface more powerfull and easy to use.- Easy to update in future ( no need to download full package).
- More models and solutions are added.
. Models and Solutions
1100/2300: car,charge,earpiece,speaker,local mode,micro,network,on/off,ring,sim
1110/1600/2310: buzzer,charge,handsfree,keypad,lcd,lcd light,light,sim,test mode
1200: charge,keypad,lcd,light,micro,on/off,sim,speaker,test mode
1650: dislay light,on/off,ring,test mode
2600: buzzer,car,charge,lcd,light,test mode
2610: audio,car,charge,lcd,micro,test mode
2630: charge,on/off,test mode
2650: car,display,headset,light,micro,ring,sim
2660: light,sim
2760: charge,sim
3100: antenna,blue lcd,charge,lcd,lcd light,local mode,on/off,ring,sim,sim track
3110: charge,display,display2,ear,speaker,keypad,light,m icro,mmc,on/off,sim,spaeker
3200: camera,charge,display,keypad,lcd,light,local mode,on/off,ring,sim
3220/6020: camera,charge,headset,keypad,lcd,led,local mode,micro,on/off,sim
3230: audio,camera,ear,hang,headset,joystick,keypad,lcd, lcd light,led,mmc,on/off,spaeker
3250: bt,camera,charge,display,earpiece,keypad,lcd,micro ,mmc,on/off,signal,sim
3650: blank,camera,display,headset,keypad,lcd,led,micro, mmc,on/off,sim,speaker,vibra,white
5100: lcd,sim
5140: camera,lcd,
5200/5300: buzzer,camera,charge,display,keypad,lcd light,light,micro,mmc,network,on/off,sim
5310: buzzer,camera,charge,display,earpiece,flex,full,ke ypad,lcd,micro,mmc,network,on/off,sim
5500: audio,display,keypad,network,ring,sim,speaker
5610: micro,on/off
5700: buzzer,micro
6030: keypad,lcd,lcd light,micro,buzzer,charge,test mode,lcd,lcd light,sim
6060: charge,local mode,sim
6070: buzzer,camera,charge,keypad,lcd,lcd light,local mode,on/off,sim,speaker
6085: handsfree,micro,sim
6101: buzzer,lcd light,light,local mode,sim
6110: micro
6120: buzzer,keypad,lcd,light,vibra,vol keys
6125: charge,keypad,camera,micro,sim
6131: blank,charge,keypad,led,micro,mmc,on/off
6151: sim
6170: down keys,keypad,local mode
6230: buzzer,camera,charge,gallery,keypad,led,light,mmc, on/off,sim,test mode,vol keys
6233: audio,bt,bsi,camera,charge,display,ear,keypad,lcd, led,micro,mmc,network,ring,sim,slide keys,vol keys
6260: charge,keypad,lcd,light,micro,mmc,on/off,ring,sim
6263: buzzer,keypad
6267: buzzer,charge,on/off,vibra,camera
6270: camera,charge,display,headset,keypad,led,light,mic ro,network
6280: blank,bt,camera,charge,display,keypad,lcd led,mmc,on/off,signal,sim
6300: blue lcd,bt,camera,charge,display,keypad,lcd,lcd light,led,micro,mmc,network,not power,on/off,ring,sim,spaeker,vibra
6500c: charge
6500s: camera
6600: batt,blank,buzzer,camera,charge,display,earpiece,g allery,joystick,keyboard,keypad,lcd led,micro,mmc,network,on/off,sim,spaker,vibra
6610/7210: lcd,light,not power,on/off,ring,sim
6630: audio,bt,camera,charge,display,earpiece,headset,ke ypad,light,mico,not power,on/off,sim,speaker,vibra,white
6670/7610: camera,charge,display,ear,keyboard,lcd,micro,on/off,ring,sim
6680: bt,camera,display,handfree,keypad,light,mmc,networ k,on/off,signal,sim,white
7200: led,local mode,sim
7250: micro,lcd,not power,light
7360: headset,keys,light,sim,speaker
7370: charge,keypad,local mode,vol keys
7373: mmc,sim
7390: charge
7500: camera,charge
7710: blank,display,mmc
8800: light,sim
E50 : audio,charge,joystick,keypad,micro,mmc
E60 : bt,buzzer,charge,display,keypad,light,on/off,sim,speaker,vibra,white
E61 : audio,blank,charge,joystick,lcd,on/off,signal,sim
E65 : display,keypad,lcd,light,offline,white
N70 : Audio,bt,camera,charge,ear,flash light,handfree,keypad,lcd,light,micro,missmatch,mm c,on/off,ring,signal,sim,synchro,white
N73 : charge,front cam,joystick,keypad,led,micro,ear,mmc,network,on/off,sim,speaker,vibra,white
N80 : charge,hang,keypad,lcd,light,mmc,network,on/off,ring,svc,white
N81 : boot,camera
N90 : charge,keypad,micro,network,sim
N91 : charge,display,ear,handfree,hang,hdd,keypad,on/off,vibra,white
N93 : charge,keypad,micro,offline
N95 : audio,bluelcd,bt,cam keys,camera,charge,flash cam,keypad,lcd,lcd led,lightmmc,network,on/off,restart,sim,usb,vibra
download here
New Latest Nokia Fbus and UFC Cable Finder ver 1.01 (Sep-19-09)
New Latest Nokia Fbus and UFC Cable Finder ver 1.01 (Sep-19-09)
- Phone Image:
- UFC Pinout:
- Phone Series:
- Phone Type:
- Asic Type:
- Cable Name:
- Compatible with:
SL3-Nokia-Hati-hati flashing!!!
Untuk rekan2 yg belum tau, harap hati2 dalam flashing HP nokia type baru.
Security Firmware nokia yg terbaru SimLock2 (SL2) terbaru, sebut aja SL3 ya..
belum dapat di downgrade atau di unlock...Kesalahan flash/unlock dapat menyebabkan kerusakan pada security area, akibatnya Contact Service, IMEI cantik.
Denger2 gak dapat ubah versi karena Firmwarenya juga dilock pada security SL3 ini.
10Mei 2009, Saat ini, belum ada solusinya...
Berikut daftar di bawah untuk tipe dan versi hp yang memiliki Security SL3.
5310 (RM-303 V58.58 ORANGE)
6500c (RM-265 V59.45 ORANGE )
6500s (RM-240 V59.60 ORANGE)
2630 (RM-298 V57.20)
Bagi rekan2 yang telah terlanjur flash hp tersebut, dapat mengembalikannya ke keadaan normal dengan cara re-flash ke versi yg sama seperti sebelumnya.Kumpulan firmware SL3:
Security Firmware nokia yg terbaru SimLock2 (SL2) terbaru, sebut aja SL3 ya..
belum dapat di downgrade atau di unlock...Kesalahan flash/unlock dapat menyebabkan kerusakan pada security area, akibatnya Contact Service, IMEI cantik.
Denger2 gak dapat ubah versi karena Firmwarenya juga dilock pada security SL3 ini.
10Mei 2009, Saat ini, belum ada solusinya...
Berikut daftar di bawah untuk tipe dan versi hp yang memiliki Security SL3.
5310 (RM-303 V58.58 ORANGE)
6500c (RM-265 V59.45 ORANGE )
6500s (RM-240 V59.60 ORANGE)
2630 (RM-298 V57.20)
Bagi rekan2 yang telah terlanjur flash hp tersebut, dapat mengembalikannya ke keadaan normal dengan cara re-flash ke versi yg sama seperti sebelumnya.Kumpulan firmware SL3:
update mx key v3.2 rev 5.4
mobileEx_setup_v3.2_rev5.4.exe
v3.2 revision 5.4, Public-Release #Minor update
- MAIN
Refixed, Windows Vista & Windows 7 compability.
- NK
Added, BB5 'Restore SIMLOCK' from '*SIMLOCK.back' or '*.PM' or '*.RPL'
~ The button located at 'IMEI & Security'->'IMEI Rebuild'->'Restore SIMLOCK'
Fixed, DCT4 unknown flash bug(BUS check)
Fixed, DCT4 CS repair when phone could not go into LOCAL MODE
Refixed, DCT4 bootstrap for UFS interface
Fake Progressbar for BB5 flash erase reenabled.
- VCOM
Recompiled PK83.bin for new api compability
v3.2 revision 5.4, Public-Release #Minor update
- MAIN
Refixed, Windows Vista & Windows 7 compability.
- NK
Added, BB5 'Restore SIMLOCK' from '*SIMLOCK.back' or '*.PM' or '*.RPL'
~ The button located at 'IMEI & Security'->'IMEI Rebuild'->'Restore SIMLOCK'
Fixed, DCT4 unknown flash bug(BUS check)
Fixed, DCT4 CS repair when phone could not go into LOCAL MODE
Refixed, DCT4 bootstrap for UFS interface
Fake Progressbar for BB5 flash erase reenabled.
- VCOM
Recompiled PK83.bin for new api compability
Selasa, 25 Agustus 2009
Security SIMLOCK NOKIA.. !!! Harus tau yaaah
BB5 PA_SL1 (read:Security Application SimLock)
RAP3GV2
* 6630
* 6680
* 6681
* N70
* N90
Rap3Gv3
* 3109c
* 3110c
* 3250
* 3500c
* 3500cb
* 5200
* 5200b
* 5300
* 5300b
* 5500
* 6085
* 6086
* 6086b
* 6125
* 6126
* 6133
* 6131
* 6131 NFC
* 6136
* 6151
* 6233
* 6234
* 6280
* 6300
* 6300b
* 7370
* 7373
* 7390
* 8600
* E50
* E50
* E50
* E61
* E61i
* E62
* E65
* E90
* N73-1
* N73-5
* N75
* N77
* N80-1
* N80-3
* N92
* N95
PA_SL2................
BB5+ RAP3GV3
* 3120c
* 3555
* 3555b
* 5310
* 5310b
* 5610
* 5610d
* 6263
* 6300i
* 6301
* 6500s
* 6500c
* 6555
* 7500
* 7900
* 8800 Arte
BB5+ RAPIDO
* 5320
* 5800
* 6110
* 6120
* 6121
* 6124
* 6210
* 6220c
* 6290
* 6650
* E51
* E63
* E66
* E71
* N78
* N81
* N81 8gb
* N76
* N79
* N85
* N82
* N95 8gb
* N96
BB5 PA_SL2 tanpa Proteksi di Firmware
RAPS_V3.03-PA_SL2 CPU
* 3600 slide
* 5220 XpressMusic
* 7210 Supernova
* 7310 Supernova
* 7610 Supernova
* 7510a
RAP3GS_V3.02-PA_SL2 CPU
* 6600 fold
* 6600 slide
BB5 PA_SL3 atawa (PA_SL2 Dengan Proteksi di Firmware)
* 5310 RM-303 - MCU SW 58.58, MCU SW 59.42 . *ORANGE
* 6300 RM-217 - MCU SW 57.20 *ORANGE
* 6500c RM-265 - MCU SW 59.45 *ORANGE
* 6500s RM-240 - MCU SW 59.60 *ORANGE
dan type baru yg belon ada firmware nya. :pound:
based on RAPS_V3.03-PA_SL2 CPU
* 3600 slide (RM-352)
* 5220 XpressMusic (RM-410/RM411)
* 7210 Supernova (RM-436)
* 7310 Supernova (RM-378/RM-379)
* 7610 Supernova (RM-354)
based on RAP3GS_V3.02-PA_SL2 CPU
* 6600 fold (RM-325)
* 6600 slide (RM-414)
DCT4+ new Security SIMLOCK2 dengan proteksi Firmware
* 2630 RM-298 - MCU SW 57.20
* 7100supernova * new asic and MCU ID 3168 .
untuk Sementara ini PA_SL2 dengan proteksi di firmware (baca:PA_SL3)
Tidak akan bisa memperbaiki SIMLOCK... tapi hanya bisa Memperbaiki IMEI saja.
Jadi sebelum ASK2RPL BB5 liat dulu type Secuirty nya.
SL2 lama atau SL2 baru(SL3).
cara nya ??.... kan di atas sdh ada CPU base nya. OK !
Kalo untuk DCT 4+ SL2 baru nya kayak nya NOKIA ngga Kejam deeh....
Setalah Downgrade HP akan mati atau Conser dan bisa di kembalikan seperti semula dengan mengembalikan ke MCU versi asalnya.
RAP3GV2
* 6630
* 6680
* 6681
* N70
* N90
Rap3Gv3
* 3109c
* 3110c
* 3250
* 3500c
* 3500cb
* 5200
* 5200b
* 5300
* 5300b
* 5500
* 6085
* 6086
* 6086b
* 6125
* 6126
* 6133
* 6131
* 6131 NFC
* 6136
* 6151
* 6233
* 6234
* 6280
* 6300
* 6300b
* 7370
* 7373
* 7390
* 8600
* E50
* E50
* E50
* E61
* E61i
* E62
* E65
* E90
* N73-1
* N73-5
* N75
* N77
* N80-1
* N80-3
* N92
* N95
PA_SL2................
BB5+ RAP3GV3
* 3120c
* 3555
* 3555b
* 5310
* 5310b
* 5610
* 5610d
* 6263
* 6300i
* 6301
* 6500s
* 6500c
* 6555
* 7500
* 7900
* 8800 Arte
BB5+ RAPIDO
* 5320
* 5800
* 6110
* 6120
* 6121
* 6124
* 6210
* 6220c
* 6290
* 6650
* E51
* E63
* E66
* E71
* N78
* N81
* N81 8gb
* N76
* N79
* N85
* N82
* N95 8gb
* N96
BB5 PA_SL2 tanpa Proteksi di Firmware
RAPS_V3.03-PA_SL2 CPU
* 3600 slide
* 5220 XpressMusic
* 7210 Supernova
* 7310 Supernova
* 7610 Supernova
* 7510a
RAP3GS_V3.02-PA_SL2 CPU
* 6600 fold
* 6600 slide
BB5 PA_SL3 atawa (PA_SL2 Dengan Proteksi di Firmware)
* 5310 RM-303 - MCU SW 58.58, MCU SW 59.42 . *ORANGE
* 6300 RM-217 - MCU SW 57.20 *ORANGE
* 6500c RM-265 - MCU SW 59.45 *ORANGE
* 6500s RM-240 - MCU SW 59.60 *ORANGE
dan type baru yg belon ada firmware nya. :pound:
based on RAPS_V3.03-PA_SL2 CPU
* 3600 slide (RM-352)
* 5220 XpressMusic (RM-410/RM411)
* 7210 Supernova (RM-436)
* 7310 Supernova (RM-378/RM-379)
* 7610 Supernova (RM-354)
based on RAP3GS_V3.02-PA_SL2 CPU
* 6600 fold (RM-325)
* 6600 slide (RM-414)
DCT4+ new Security SIMLOCK2 dengan proteksi Firmware
* 2630 RM-298 - MCU SW 57.20
* 7100supernova * new asic and MCU ID 3168 .
untuk Sementara ini PA_SL2 dengan proteksi di firmware (baca:PA_SL3)
Tidak akan bisa memperbaiki SIMLOCK... tapi hanya bisa Memperbaiki IMEI saja.
Jadi sebelum ASK2RPL BB5 liat dulu type Secuirty nya.
SL2 lama atau SL2 baru(SL3).
cara nya ??.... kan di atas sdh ada CPU base nya. OK !
Kalo untuk DCT 4+ SL2 baru nya kayak nya NOKIA ngga Kejam deeh....
Setalah Downgrade HP akan mati atau Conser dan bisa di kembalikan seperti semula dengan mengembalikan ke MCU versi asalnya.
Senin, 20 Juli 2009
Upgrade BI smartphone SE P1,P990,M600,W950 tanpa harus flash
-instal Sony_Ericsson_PC_Suite_for_Smartphones_1_3_33 dan siapkan kabel DCU-60
-connect hp ke DCU-60 jika minta driver arahkan ke C:\Program Files\Sony Ericsson\Sony Ericsson Symbian 9 Drivers
-buka PC suite SE klik aplication installer
cari file yang udah kita download lalu klik next
proses instalasi berjalan tunggu sampe finish dan instalasi akan di lanjutkan ke HP
setelah finish ini hasil nya
semua file nya bisa di Download disini http://www.sonyericsson.com/cws/mark...rtment.Support
-connect hp ke DCU-60 jika minta driver arahkan ke C:\Program Files\Sony Ericsson\Sony Ericsson Symbian 9 Drivers
-buka PC suite SE klik aplication installer
cari file yang udah kita download lalu klik next
proses instalasi berjalan tunggu sampe finish dan instalasi akan di lanjutkan ke HP
setelah finish ini hasil nya
semua file nya bisa di Download disini http://www.sonyericsson.com/cws/mark...rtment.Support
Rabu, 15 Juli 2009
Selasa, 14 Juli 2009
kode rahasia i-phone
Here are some more secret iPhone codes for you to enjoy. After realizing that the *3001#12345#* was a familiar Nokia code, I decided to spend some time googling for other phone codes that might work on the iPhone.
These (mostly) do. There are more. Feel free to add your own to the comments.
*3001#12345#* and tap Call. Enter Field Mode.Field mode reveals many of the inner settings of your iPhone, specifically up-to-date network and cell information.
*#06# Displays your IMEI. No need to tap Call.IMEI is the unique identifier for your cell phone hardware. Together with your SIM information it identifies you to the provider network.
*777# and tap Call. Account balance for prepaid iPhone.
*225# and tap Call. Bill Balance. (Postpaid only)
*646# and tap Call. Check minutes. (Postpaid only)These three are pretty self explanatory.
*#21# and tap Call. Setting interrogation for call forwards.Discover the settings for your call forwarding. You'll see whether you have voice, data, fax, sms, sync, async, packet access, and pad access call forwarding enabled or disabled.
*#30# and tap Call. Calling line presentation check.This displays whether you have enabled or disabled the presentation of the calling line, presumably the number of the party placing the call.
*#76# and tap Call. Check whether the connected line presentation is enabled or not.State whether the connected line presentation is enabled or disabled. Presumably similar to the calling line presentation.
*#43# and tap Call. Determine if call waiting is enabled.Displays call waiting status for voice, data, fax, sms, sync data, async data, packet access and pad access. Each item is either enabled or disabled.
*#61# and tap Call. Check the number for unanswered calls.Show the number for voice call forwarding when a call is unanswered. Also show the options for data, fax, sms, sync, async, packet access and pad access.
*#62# and tap Call. Check the number for call forwarding if no service is available.Just like the previous, except for no-service rather than no-answer situations.
*#67# and tap Call. Check the number for call forwarding when the iPhone is busy.And again, but for when the iPhone is busy.
*#33# and tap Call. Check for call control bars.Check all the usual suspects (voice, data, fax, sms, etc) to see whether barring is enabled or disabled for outgoing.
saya belum mencoba semua kode yang saya tulis diatas ini,apabila ada sesuatu yang ganjil kita bahas bersama
These (mostly) do. There are more. Feel free to add your own to the comments.
*3001#12345#* and tap Call. Enter Field Mode.Field mode reveals many of the inner settings of your iPhone, specifically up-to-date network and cell information.
*#06# Displays your IMEI. No need to tap Call.IMEI is the unique identifier for your cell phone hardware. Together with your SIM information it identifies you to the provider network.
*777# and tap Call. Account balance for prepaid iPhone.
*225# and tap Call. Bill Balance. (Postpaid only)
*646# and tap Call. Check minutes. (Postpaid only)These three are pretty self explanatory.
*#21# and tap Call. Setting interrogation for call forwards.Discover the settings for your call forwarding. You'll see whether you have voice, data, fax, sms, sync, async, packet access, and pad access call forwarding enabled or disabled.
*#30# and tap Call. Calling line presentation check.This displays whether you have enabled or disabled the presentation of the calling line, presumably the number of the party placing the call.
*#76# and tap Call. Check whether the connected line presentation is enabled or not.State whether the connected line presentation is enabled or disabled. Presumably similar to the calling line presentation.
*#43# and tap Call. Determine if call waiting is enabled.Displays call waiting status for voice, data, fax, sms, sync data, async data, packet access and pad access. Each item is either enabled or disabled.
*#61# and tap Call. Check the number for unanswered calls.Show the number for voice call forwarding when a call is unanswered. Also show the options for data, fax, sms, sync, async, packet access and pad access.
*#62# and tap Call. Check the number for call forwarding if no service is available.Just like the previous, except for no-service rather than no-answer situations.
*#67# and tap Call. Check the number for call forwarding when the iPhone is busy.And again, but for when the iPhone is busy.
*#33# and tap Call. Check for call control bars.Check all the usual suspects (voice, data, fax, sms, etc) to see whether barring is enabled or disabled for outgoing.
saya belum mencoba semua kode yang saya tulis diatas ini,apabila ada sesuatu yang ganjil kita bahas bersama
pengecekan short pada hp nokia 3100
check shoting in nokia 3100.....1..remove both coil mark in (1)...to check the shoting cause pf.....
2..remove light ic n300 mark in (2)...to check the shoting cause by the light ic....
3..remove accessory regulator ic n100 mark in (3)....to check the shoting cause by it because this ic got +b from batery......
4..remove ringer ic n150 mark in (4)...to check the shoting cause by ringer ic......
5..at end remove uem to check shoting is gone or not........
all the component which are mark in pink colur these all are coils and resistance these are place in series and +b of batery is gone throw them so if u remove the coil u not have to remove ic to check the shorting in pcb it save time and ur ic ....
pengecekan short pada hp nokia 6280
check shoting in nokia 6280....1..remove this l7520 mark in (1) if u want to check the shoting of pf of gsm and wcdma ....if remove the coil and ur shoting is gone then tere is shoting in ur pf of gsm or wcdma ........
2..remove this coil mark in l7500 (2)...if u want to check the shoting of rf ic for .... by removing this coil if ur shoting is gone then there is shoting in ur rf ic .....
3...remove this resistance mark in (3) to check the bluetooth module ... to check shoting ...because it got +b from batery.....
4..remove this resistance mark in (4) to check the n6050 power supply maker ic ....it make suplly for fm radio...it got +b from batery remove resistance to check shoting cause by this ic....
5..remove this resistance mark in (5) to check the shoting cause by irda ....because irda got the +b from batery......
6...remove this coil mark in (6) to check memory card driver ic n3200 .....because this ic got +b from batery....
7..remove this coil mark in (7)..if u want to check the light ic is short....
8..remove this ic mark in (
...it is vcam maker ic which make vcam for camera ......remove this ic to check shoting because this ic got +b from batery......9..remove this mark in (9) ...it is flash light driver ic ......remove it to check shoting cause by it or not.....
10.. at end remove retu and tahvo ic to check shoting is gone r not.......
all the component which are mark in pink colur these all are coils and resistance these are place in series and +b of batery is gone throw them so if u remove the coil u not have to remove ic to check the shorting in pcb it save time and ur ic ....
pengecekan short pada hp nokia N91
check shoting in nokia n-91........1..remove this z7500 mark in (1) if u want to check the shoting of pf of gsm and wcdma ....if remove the coil and ur shoting is gone then tere is shoting in ur pf of gsm or wcdma ........
2..remove this coil mark in l7503 (2)...if u want to check the shoting of rf ic for gsm hinku and rf ic for wcdma vinku.... by removing this coil if ur shoting is gone then there is shoting in ur rf ic whether it is hinku or vinku.....under shield..cover....
3..remove this coil mark in (3)..if u want to check the shorting cause by (vdac) maker ic n2101 which make vdac for audio-dac ic n2100.........remove this coil to chec shoting .....because this ic got +b from batery....
4..remove this coil mark in (4)..if u want to check smps ic n4200.. ..this ic make v corea for omap ic and rap remove cil to check shoting is gone or not.....
5..remove this ic n5000 ape regulator mark in (5)..if u want to check the shoting is cause by this remove it to check shoting is gone or not....
6..remove light ic mark in (6) ... to check the shoting cause by light ic or not....
7..remove coil mark in (7) ...it is vcam maker ic which make (vdd logic) ......remove this coil to check shoting because this ic got +b from batery......
8..remove coil. mark in (
... it is cam maker ic which make (vdd analog) for camera ....remove these coil to check shoting .....because it got +b from batery.....9..remove bluetooth module mark in (9)... to check shoting ...because it got +b from batery.....
10..remove this coil mark in (10)...to check the ic n5205 which make voltage (vhdd)... for the 4gb & 8gb hard disk......this ic got +b from batery.......
11..remove wlan pa mark in (11) ...to check shoting because this ic got +b from batery.....
12..remove wlan ic n6300 mark in (12) ....to check the shoting because this ic got +b from batery..........
all the component which are mark in pink colur these all are coils these are place in series and +b of batery is gone throw them so if u remove the coil u not have to remove ic to check the shorting in pcb it save time and ur ic ....
pengecekan short pada hp nokia 1650 dct4+
check shoting in nokia 1650,1200,1208......1..remove this coil mark in (1)..if u want to check the light ic is short....
2..remove ringer ic mark in (2)..if u want to check shoting remove it and check if shoting is gone replace it because ringer ic also got +b volt from battery....
3..remove the network ic n7100 mark in (1)...if u want to check this ic is short remove it and check shoting...if it is shot then replace it...
4..at end check the power ic d2901 mark in (4) and reemove it to check shoting is there or not...
all the component which are mark in pink colur these all are coils these are place in series and +b of batery is gone throw them so if u remove the coil u not have to remove ic to check the shorting in pcb it save time and ur ic ....
pengecekan short pada hp nokia 6070
|
pengecekan short pada hp nokia 2630 dct4+
check shorting in nokia dct4++ 2630.....1..remove the pf n7700 mark in (1)...if u want to check is pf is short remove it and check shoting...if it is shot then replace it...
2..remove this coil mark in (2)..if u want to check the light ic is short....
3..remove ringer ic mark in (3)..if u want to check shoting remove it and check if shoting is gone replace it because ringer ic also got +b volt from battery....
4..remove this v.camdig ic n3301 mark in (4)..if u want to check the v.camdig maker ic ..this v.camdig maker ic got +b from batery....to make v,cam for camera.....
5..remove this ic n6000 bluetooth and fm ic mark in (5)..if u want to check the shoting cause by it remove it and check shoting because it got =b from batery....
6..at end check the power ic and reemove it to check shoting is there or not...
all the component which are mark in pink colur these all are coils these are place in series and +b of batery is gone throw them so if u remove the coil u not have to remove ic to check the shorting in pcb it save time and ur ic ....
pengecekan short pada hp nokia 6111
check shoring in nokia 6111...
1..remove this coil mark in (1)...if u want to check is pf is short,.....
2..remove this coil mark in (2)..if u want to check the light ic is short....
3..remove this coil mark in (3)..if u want to check flash light driver ic is short because flash light driver ic also got +b volt from battery....
4..remove this boot ic mark in (4)..if u want to check the shorting is made by boot ic .....it is often damage in water damage set ....replace ith new one if it cause shorting......
5..remove this n2371 mark in (5)..if u want to check the v.camdig maker ic which make v camdig for camera ...it also got +b from batery.....
6.. check the n2370r ic ...it make vcorea suplyy for cpu ... it also got +b it can be check by only removing this ic.....
7..remove ringer ic mark in (7) to check shorting is gone or not...
8..remove bluetooth ic to check shoting is gone mark in
9..remove uem to check shorting......
pengecekan short pada hp nokia 3500 n 3110 c
check shorting in 3500....and 3110...
1..remove this coil mark in (1)...if u want to check is pf is short,.....
2..remove this coil mark in (2)..if u want to check rf ic is short because rf ic also got +b volt from battery....
3..remove this coil mark in (3)..if u want to check blutooth ic is short because bluetooth ic also got +b volt from battery....
4..remove this coil mark in (4)..if u want to check the v.camdig maker ic ..this v.camdig maker ic got +b from batery....
5..remove this coil mark in (5)..if u want to check the light ic is short....
6..also check the memory card driver ic n3200 it also got +b it can be check by only removing this ic.....
7..at end remove retu and tahvo ic ..
all the component which are mark in pink colur these all are coils these are place in series and +b of batery is gone throw them so if u remove the coil u not have to remove ic to check the shorting in pcb it save time and ur ic ....
pengecekan short pada hp nokia 5200 n 5300
check shoting in 5200 and 5300.....
1..remove this coil mark in (1)...if u want to check is pf is short,.....
2..remove this coil mark in (2)..if u want to check rf ic is short because rf ic also got +b volt from battery....
3..remove this coil mark in (3)..if u want to check blutooth ic is short because bluetooth ic also got +b volt from battery....
4..remove this ic ..if u want to check the v.camdig maker ic ..this v.camdig maker ic got +b from batery....
5..remove this coil mark in (5)..if u want to check the light ic is short....
6..also check the memory card driver ic n3200 it also got +b it can be check by only removing this ic.....
7..at end remove retu and tahvo ic...
all the component which are mark in pink colur these all are coils these are place in series and +b of batery is gone throw them so if u remove the coil u not have to remove ic to check the shorting in pcb it save time and ur ic ....
pengecekan short pada hp nokia 6300
check shorting in 6300...
1..remove this coil mark in (1)...if u want to check is pf is short,.....
2..remove this coil mark in (2)..if u want to check rf ic is short because rf ic also got +b volt from battery....
3..remove this coil mark in (3)..if u want to check blutooth ic is short because bluetooth ic also got +b volt from battery....
4..remove this coil mark in (4)..if u want to check the v.camdig maker ic ..this v.camdig maker ic got +b from batery....
5..remove this coil mark in (5)..if u want to check the light ic is short....
6..also check the memory card driver ic n3200 it also got +b it can be check by only removing this ic.....
7..at end remove retu and tahvo ic...
all the component which are mark in pink colur these all are coils these are place in series and +b of batery is gone throw them so if u remove the coil u not have to remove ic to check the shorting in pcb it save time and ur ic ....
Kamis, 21 Mei 2009
solusi BB5
Ponsel Nokia terbaru yang memiliki dual processor adalah golongan BB5. Ponsel golongan ini memiliki kecanggihan yang tidak dimiliki oleh golongan Nokia sebelumnya (DCT3, DCT4, DCT4WD2). Ponsel Nokia BB5 seperti Nokia 6630, 6680, 6680, 6681, N Series.
CMT ERROR?? APE ERROR? Di Sini Jawabnya
CMT ERROR?? APE ERROR? Di Sini Jawabnya>>>>
________________________________________
memngingat banyak yang buka thread dengan judul:
tolong CMT ERROR!!!!!!!!!!!
tolong APE ERROR!!!!!!!!!!!
dan banyak yang memberi solusi meleset dari hal tersebut
maka ada baiknya di buat satu thread stuck untuk 2 masalah ini
sebenarnya banyak yang thread yang mengupas tuntas masalah ini tapi buat mempermudah pencarian gak apa2 dibuat thrad ini
dalam hal ini hanya sekedar garis besarnya aja dan langsung pada sasarannya aja
pada HP dual CPU (RAP + OMAP) APE dan CMT hadir keduanya
tapi pada single CPU (hanya RAP) cuma CMT dan APE absent
IC yang berperan besar pada bagian CMT:
• RAP
• RAM (kalo ada)
• IC NOR Flash
IC yang berperan besar dalam bagian APE :
• OMAP
• IC NAND Flash
• IC Regulator APE (jika ada)
maka
pada error APE yang perlu di periksa:
• tegangan kerja IC APE (NAND Flash) biasa di sebut VDDR APE
• IC NAND Flash (REHOT, REBALL atau sekalian GANTI)
• Hubungan Antara OMAP dan NAND Flash
Pada ERROR CMT yang paling perlu di periksa:
• tegangan kerja RAM dan NOR Flash
• RAM (REHOT, REBALL, GANTI)
• NOR Flash (REHOT, REBALL, GANTI)
• RAP (REHOT, REBALL, GANTI)
dan mungkin akan ditambah oleh master2 BB5 yang lebih lengkap
untuk HP yang dual CPU jika di cek di HWK muncul select product MISSMACTH
ini berarti OMAP belum bekerja (RAPGSM udah bekerja)
paling sering kehilangan tegangan VCOREA yang dihasilkan oleh IC SMPS sebesar 1,4 Volt
solusi udah sering di bahas di forum ini yakni:
• disarankan ganti SMPS
• alternatif = Jumper dari tegangan yang sama (tidak di anjurkan)
atau kadang dari OMAP sendiri yang udah koit
JANGAN sembarangan Jumper tanpa mengetahui letak kerusakannya..
N70 Blank itu terjadi akibat bagian APE (Application Processor Engine) tdk berfungsi dengan semestinya. Bisa terjadi dari IC OMAP yang bermasalah, juga NAND Flash yg bermasalah.
Namun umumnya Masalah bukan dari OMAP dan NAND Flash melainkan akibat OMAP maupun NAND Flash hilang tegangannya..
OMAP mendapatkan tegangan VCoreA 1,4V dari IC SMPS N4200, sedangkan
NAND Flash (APE Flash) mendapatkan tegangan VDRAM 1,8 V dari APE Regulator N4201.
Jadi sebelum melakukan penjumperan sembarangan sesuai tricks jumper yg banyak beredar, laukan pengukuran tegangan terlebih dahulu sbb:
1. Pasang PCB Ponsel N70 ke Power Supply dgn teg. 3,6 s/d 4,1 V
2. Tekan Power On/Off agar Bagian Regulator mengeluarkan tegangan kerja.
3. Ukur VCoreA di C4200 sebesar 1,4 Volt, jika tdk keluar lakukan Jumper VCoreA
4. Ukur VDRAM di C4206 sebesar 1,8 Volt, jika tdk keluar lakukan Jumper VDRAM
5. Jika tegangan VCoreA dan VDRAM diukur keluar normal semua, solusi Jumper tdk akan berguna, karena yg rusak adalah IC OMAP ataupun NAND Flash itu sendiri.
________________________________________
memngingat banyak yang buka thread dengan judul:
tolong CMT ERROR!!!!!!!!!!!
tolong APE ERROR!!!!!!!!!!!
dan banyak yang memberi solusi meleset dari hal tersebut
maka ada baiknya di buat satu thread stuck untuk 2 masalah ini
sebenarnya banyak yang thread yang mengupas tuntas masalah ini tapi buat mempermudah pencarian gak apa2 dibuat thrad ini
dalam hal ini hanya sekedar garis besarnya aja dan langsung pada sasarannya aja
pada HP dual CPU (RAP + OMAP) APE dan CMT hadir keduanya
tapi pada single CPU (hanya RAP) cuma CMT dan APE absent
IC yang berperan besar pada bagian CMT:
• RAP
• RAM (kalo ada)
• IC NOR Flash
IC yang berperan besar dalam bagian APE :
• OMAP
• IC NAND Flash
• IC Regulator APE (jika ada)
maka
pada error APE yang perlu di periksa:
• tegangan kerja IC APE (NAND Flash) biasa di sebut VDDR APE
• IC NAND Flash (REHOT, REBALL atau sekalian GANTI)
• Hubungan Antara OMAP dan NAND Flash
Pada ERROR CMT yang paling perlu di periksa:
• tegangan kerja RAM dan NOR Flash
• RAM (REHOT, REBALL, GANTI)
• NOR Flash (REHOT, REBALL, GANTI)
• RAP (REHOT, REBALL, GANTI)
dan mungkin akan ditambah oleh master2 BB5 yang lebih lengkap
untuk HP yang dual CPU jika di cek di HWK muncul select product MISSMACTH
ini berarti OMAP belum bekerja (RAPGSM udah bekerja)
paling sering kehilangan tegangan VCOREA yang dihasilkan oleh IC SMPS sebesar 1,4 Volt
solusi udah sering di bahas di forum ini yakni:
• disarankan ganti SMPS
• alternatif = Jumper dari tegangan yang sama (tidak di anjurkan)
atau kadang dari OMAP sendiri yang udah koit
JANGAN sembarangan Jumper tanpa mengetahui letak kerusakannya..
N70 Blank itu terjadi akibat bagian APE (Application Processor Engine) tdk berfungsi dengan semestinya. Bisa terjadi dari IC OMAP yang bermasalah, juga NAND Flash yg bermasalah.
Namun umumnya Masalah bukan dari OMAP dan NAND Flash melainkan akibat OMAP maupun NAND Flash hilang tegangannya..
OMAP mendapatkan tegangan VCoreA 1,4V dari IC SMPS N4200, sedangkan
NAND Flash (APE Flash) mendapatkan tegangan VDRAM 1,8 V dari APE Regulator N4201.
Jadi sebelum melakukan penjumperan sembarangan sesuai tricks jumper yg banyak beredar, laukan pengukuran tegangan terlebih dahulu sbb:
1. Pasang PCB Ponsel N70 ke Power Supply dgn teg. 3,6 s/d 4,1 V
2. Tekan Power On/Off agar Bagian Regulator mengeluarkan tegangan kerja.
3. Ukur VCoreA di C4200 sebesar 1,4 Volt, jika tdk keluar lakukan Jumper VCoreA
4. Ukur VDRAM di C4206 sebesar 1,8 Volt, jika tdk keluar lakukan Jumper VDRAM
5. Jika tegangan VCoreA dan VDRAM diukur keluar normal semua, solusi Jumper tdk akan berguna, karena yg rusak adalah IC OMAP ataupun NAND Flash itu sendiri.
Dan pada attachment adalah Gambar Jumper VDRAM yg lengkap, disertai skematik dan keterangannya.
Kamis, 16 April 2009
hard reset nokia 5800
kode hard reset nokia 5800
pada saat menyalakan handphone tekan tombol merah + hijau + camera secara bersamaan
(trik ini digunakan sebagai format handphone anda menjadi seperti awal kita beli,dan harap backup dulu kontak dan lain sebagainya terlebih dahulu )
semoga bermanfaat
pada saat menyalakan handphone tekan tombol merah + hijau + camera secara bersamaan
(trik ini digunakan sebagai format handphone anda menjadi seperti awal kita beli,dan harap backup dulu kontak dan lain sebagainya terlebih dahulu )
semoga bermanfaat
cara kerja BB5
Cara Kerja BB5
1.Level Shifter
IC ini berfungsi untuk mangatur jalannya data dari kamera depan ke CPU. Bila rusak, akan mengakibatkan terganggunya fungsi kamera depan sehingga tidak bisa diaktifkan.
2.64 Mbit NOR Flash
Adalah subuah IC Flash dengan kapasitas 64 Mbit. IC Flash menyimpan program-program yang harus dijalankan oleh CPU. Kerusakan IC Flash ada dua, kerusakan hardware, dan software. Kerusakan hardware adalah kerusakan pada IC itu sendiri, kerusakan software terjadi bila isi program terhapus atau berubah secara tidak sengaja. Kedua kerusakan ini menghasilkan tidak normalnya handphone, seperti hanphone mati total, hang, LCD blank, tidak ada signal, handphone terkunci, dan masih banyak lagi.
Cara perbaikannya, bila terjadi kerusakan software adalah dengan melakukan proses flashing.
3.IC TK65600B
IC ini adalah IC untuk menaikkan level tegangan DC. Bila IC ini rusak, bisa menyebabkan lampu pada layar maupun keypad handphone tidak menyala.
4.RAP 3G
Singkatan dari Radio Aplication Processor. Merupakan satu dari dua CPU yang ada di handphone BB5. Fungsi dari CPU ini tentu mengendalikan kinerja dari si hanphone, tetapi salah satu fungsi utamanya adalah mengontrol, mengolah data bagian radio dari hanphone. Bila CPU ini rusak, atau bagian dari CPU ini rusak, handphone bisa mati total, tidak ada signal, dan lain lain.
5.OMAP
Singkatan dari Open Multimedia Application Platform. Adalah CPU kedua dari sebuah handphone generasi BB5. OMAP ini juga sering disebut APE( Aplication Phone Engine). Fungsi CPU ini berbeda dengan RAP 3G. CPU ini lebih menitik beratkan pada kerja aplikasi yang ada pada handphone seperti kamera, bluetooth, LCD, Keypad, MMC, dan lain-lain. Jadi bila CPU ini bermasalah, atau bagian dari CPU ini rusak, akan menyebabkan mati total, keypad tidak bisa ditekan, Bluetooth error, MMC problem, kamera tidak berfungsi, LCD blank, dan lain
6.64 Mbit SDRAM
RAM singkatan dari Random Access Memory, adalah memory kerja CPU yang bersifat sementara dan tidak bisa menyimpan data secara permanent, bila tegangan kerja RAM hilang, bersamaan dengan itu data yang ada di RAM pun turut hilang. Bila RAM ini rusak, umumnya handphone mati total, tidak bisa diprogram ulang.
7.RETU
IC ini adalah salah satu dari dua IC power yang ada di handphone jenis BB5. Kerusakan pada IC ini bisa menyebabkan handphone mati total, tidak bisa mendapat jaringan, No network, tidak bisa membaca kartu, tidak bisa membaca MMC, gangguan pada audio, dan lain lain.
8.Combo Memory
Memory jenis ini merupakan gabungan dari Flash 256 Mbit dengan 256 Mbit RAM. Memory ini memiliki kapasitas yang cukup besar. Isi dari memory ini adalah menyimpan data data berupa program untuk menjalankan CPU OMAP. Tidak normalnya isi program pada combo memory ini akan menyebabkan banyak jenis kerusakan. Salah satu yang sering terjadi adalah LCD blank.
9.Osilator kristal 32 Khz
Komponen ini adalah sebuah osilator jenis kristal yang berfungsi menghasilkan satu gelombang dengan frekuensi 32768 Hz. Bila komponen ini bermasalah bisa mengakibatkan tidak normalnya handphone, seperti handphone tidak bisa menyala, masalah pada jam hanphone, dan lain lain
10.Anti statis
Anti statis yang fungsinya untuk melindungi IC dari listrik statis kali ini dipakai untuk melindungi CPU dari listrik statis yang mungkin masuk melalui konektor keypad. Jadi bila IC ini rusak bisa menyebabkan tidak berfungsinya keypad, atau sering disebut juga dengan istilah “keypad hank”
11.Rangkaian LM 2708
Rangkain IC ini membentuk suatu rangkaian SMPS(Switch Mode Power Supply). Atau rangkaian power supply dengan sistim switching. Rangkaian ini menghasilkan satu tegangan sebesar 1,4 Volt yang disebut dengan Vcore A. Tegangan ini adalah tegangan kerja untuk CPU OMAP. Jadi bila ada masalah pada rangkaian ini, OMAP tidak bekerja normal, handphnone akan mati total.
12.Konektor antenna WCDMA
Handphone BB5 seperti handphone N70 memiliki dua sistem, GSM dan WCDMA. Konektor antenna WCDMA ini bila kotor atau bad connect akan menyebabkan terjadi gangguan signal pada jaringan WCDMA.
13.Antena switch WCDMA
Fungsi dari komponen ini adalah memisahkan antara signal RX (Receiver) dan signal TX(transmitter). Bila rusak akan mengganggu sistem radio pada sistem WCDMA.
14.Regulator kamera
Regulator ini fungsinya memberikan tegangan yang stabil untuk kamera depan. Gangguan pada rangkaian IC ini dan rangkaiannya akan menyebabkan tidak berfungsinya kamera depan pada handphone N70 ini.
15.Rangkaian PA dan pengontrolnya
Rangkaian ini berfungsi untuk memperkuat signal pemancar band WCDMA. IC PA sering juga disebut penguat akhir. Bila komponen ini rusak, maka handphone akan sulit dipakai untuk menelepon. Atau bisa juga menyebabkan handpone tidak ada indicator signal sama sekali.
16.DC/DC converter untuk lampu flash
Rangkaian ini dipakai untuk menyalakan lampu flash ketika sedang memotret gambar. Cara kerjanya adalah menaikkan level tegangan DC menjadi level tegangan yang lebih tinggi. Bila rangkaian ini bermasalah, akan mengganggu fungsi lampu flash.
17.HINKU
IC ini boleh juga disebut dengan RX Processor. Fungsinya untuk mengolah signal RX baik GSM maupun WCDMA. Bila IC ini rusak atau tidak normal kerjanya akan mengakibatkan handphnoe tidak ada signal, signal penerima lemah, dan sebagainya.
18.Filter RX
Filter ini fungsinya sebagai penyaring. Jika terjdi masalah pada komponen ini, signal penerima akan terganggu. Karena ini adalah filter WCDMA, maka akan terjadi gangguan pada band WCDMA, bila filter ini bermasalah.
19.VINKU
Adalah IC yang berfungsi untuk mengolah signal TX. IC ini bisa mengolah signal TX baik GSM maupun WCDMA. Kalau IC ini bermasalah akan menyebabkan masalah pada pemancar. Gejala yang muncul adalah handphone sulit untuk telepon, juga sulit untuk menerima telepon, bisa juga tidak ada signal sama sekali.
1.Level Shifter
IC ini berfungsi untuk mangatur jalannya data dari kamera depan ke CPU. Bila rusak, akan mengakibatkan terganggunya fungsi kamera depan sehingga tidak bisa diaktifkan.
2.64 Mbit NOR Flash
Adalah subuah IC Flash dengan kapasitas 64 Mbit. IC Flash menyimpan program-program yang harus dijalankan oleh CPU. Kerusakan IC Flash ada dua, kerusakan hardware, dan software. Kerusakan hardware adalah kerusakan pada IC itu sendiri, kerusakan software terjadi bila isi program terhapus atau berubah secara tidak sengaja. Kedua kerusakan ini menghasilkan tidak normalnya handphone, seperti hanphone mati total, hang, LCD blank, tidak ada signal, handphone terkunci, dan masih banyak lagi.
Cara perbaikannya, bila terjadi kerusakan software adalah dengan melakukan proses flashing.
3.IC TK65600B
IC ini adalah IC untuk menaikkan level tegangan DC. Bila IC ini rusak, bisa menyebabkan lampu pada layar maupun keypad handphone tidak menyala.
4.RAP 3G
Singkatan dari Radio Aplication Processor. Merupakan satu dari dua CPU yang ada di handphone BB5. Fungsi dari CPU ini tentu mengendalikan kinerja dari si hanphone, tetapi salah satu fungsi utamanya adalah mengontrol, mengolah data bagian radio dari hanphone. Bila CPU ini rusak, atau bagian dari CPU ini rusak, handphone bisa mati total, tidak ada signal, dan lain lain.
5.OMAP
Singkatan dari Open Multimedia Application Platform. Adalah CPU kedua dari sebuah handphone generasi BB5. OMAP ini juga sering disebut APE( Aplication Phone Engine). Fungsi CPU ini berbeda dengan RAP 3G. CPU ini lebih menitik beratkan pada kerja aplikasi yang ada pada handphone seperti kamera, bluetooth, LCD, Keypad, MMC, dan lain-lain. Jadi bila CPU ini bermasalah, atau bagian dari CPU ini rusak, akan menyebabkan mati total, keypad tidak bisa ditekan, Bluetooth error, MMC problem, kamera tidak berfungsi, LCD blank, dan lain
6.64 Mbit SDRAM
RAM singkatan dari Random Access Memory, adalah memory kerja CPU yang bersifat sementara dan tidak bisa menyimpan data secara permanent, bila tegangan kerja RAM hilang, bersamaan dengan itu data yang ada di RAM pun turut hilang. Bila RAM ini rusak, umumnya handphone mati total, tidak bisa diprogram ulang.
7.RETU
IC ini adalah salah satu dari dua IC power yang ada di handphone jenis BB5. Kerusakan pada IC ini bisa menyebabkan handphone mati total, tidak bisa mendapat jaringan, No network, tidak bisa membaca kartu, tidak bisa membaca MMC, gangguan pada audio, dan lain lain.
8.Combo Memory
Memory jenis ini merupakan gabungan dari Flash 256 Mbit dengan 256 Mbit RAM. Memory ini memiliki kapasitas yang cukup besar. Isi dari memory ini adalah menyimpan data data berupa program untuk menjalankan CPU OMAP. Tidak normalnya isi program pada combo memory ini akan menyebabkan banyak jenis kerusakan. Salah satu yang sering terjadi adalah LCD blank.
9.Osilator kristal 32 Khz
Komponen ini adalah sebuah osilator jenis kristal yang berfungsi menghasilkan satu gelombang dengan frekuensi 32768 Hz. Bila komponen ini bermasalah bisa mengakibatkan tidak normalnya handphone, seperti handphone tidak bisa menyala, masalah pada jam hanphone, dan lain lain
10.Anti statis
Anti statis yang fungsinya untuk melindungi IC dari listrik statis kali ini dipakai untuk melindungi CPU dari listrik statis yang mungkin masuk melalui konektor keypad. Jadi bila IC ini rusak bisa menyebabkan tidak berfungsinya keypad, atau sering disebut juga dengan istilah “keypad hank”
11.Rangkaian LM 2708
Rangkain IC ini membentuk suatu rangkaian SMPS(Switch Mode Power Supply). Atau rangkaian power supply dengan sistim switching. Rangkaian ini menghasilkan satu tegangan sebesar 1,4 Volt yang disebut dengan Vcore A. Tegangan ini adalah tegangan kerja untuk CPU OMAP. Jadi bila ada masalah pada rangkaian ini, OMAP tidak bekerja normal, handphnone akan mati total.
12.Konektor antenna WCDMA
Handphone BB5 seperti handphone N70 memiliki dua sistem, GSM dan WCDMA. Konektor antenna WCDMA ini bila kotor atau bad connect akan menyebabkan terjadi gangguan signal pada jaringan WCDMA.
13.Antena switch WCDMA
Fungsi dari komponen ini adalah memisahkan antara signal RX (Receiver) dan signal TX(transmitter). Bila rusak akan mengganggu sistem radio pada sistem WCDMA.
14.Regulator kamera
Regulator ini fungsinya memberikan tegangan yang stabil untuk kamera depan. Gangguan pada rangkaian IC ini dan rangkaiannya akan menyebabkan tidak berfungsinya kamera depan pada handphone N70 ini.
15.Rangkaian PA dan pengontrolnya
Rangkaian ini berfungsi untuk memperkuat signal pemancar band WCDMA. IC PA sering juga disebut penguat akhir. Bila komponen ini rusak, maka handphone akan sulit dipakai untuk menelepon. Atau bisa juga menyebabkan handpone tidak ada indicator signal sama sekali.
16.DC/DC converter untuk lampu flash
Rangkaian ini dipakai untuk menyalakan lampu flash ketika sedang memotret gambar. Cara kerjanya adalah menaikkan level tegangan DC menjadi level tegangan yang lebih tinggi. Bila rangkaian ini bermasalah, akan mengganggu fungsi lampu flash.
17.HINKU
IC ini boleh juga disebut dengan RX Processor. Fungsinya untuk mengolah signal RX baik GSM maupun WCDMA. Bila IC ini rusak atau tidak normal kerjanya akan mengakibatkan handphnoe tidak ada signal, signal penerima lemah, dan sebagainya.
18.Filter RX
Filter ini fungsinya sebagai penyaring. Jika terjdi masalah pada komponen ini, signal penerima akan terganggu. Karena ini adalah filter WCDMA, maka akan terjadi gangguan pada band WCDMA, bila filter ini bermasalah.
19.VINKU
Adalah IC yang berfungsi untuk mengolah signal TX. IC ini bisa mengolah signal TX baik GSM maupun WCDMA. Kalau IC ini bermasalah akan menyebabkan masalah pada pemancar. Gejala yang muncul adalah handphone sulit untuk telepon, juga sulit untuk menerima telepon, bisa juga tidak ada signal sama sekali.
Rabu, 15 April 2009
tipsn trik bb5
http://www.forum-indoflasher.com/vbb/showthread.php?t=161617 , username : zulkarnain ,pass ; 225588
Senin, 23 Maret 2009
kode handphone
Macam-macam code rahasia handphone adalah code-code yang biasa dipergunakan untuk mereparasi perangkat handphone hanya dengan menekan tombol keypad yang ada pada handphone yang telah mengalami kerusakan, kerusakan-kerusakan ini bisa tergolong ringan maupun berat, dalam teknik perbaikan ini tidak memerlukan perangkat lain atau alat bantu yang biasa digunakan untuk mereparasi pada handphone yang rusak, sedang kerusakan-kerusakan ini seperti : Hang, System Error, Aplikasi Error, Phone Lock, Searching, Dll
ERICSSON
*#06# IMEI number
*#0000# or <> Restore English menu version
> * < < * < * Version of software
< * * < Simlock info
SAMSUNG
IMEI number: * # 0 6 #
Software version: * # 9 9 9 9 # or * # 0 8 3 7 #
Net Monitor: * # 0 3 2 4 #
Memory reset (removes SIMLOCK!!!): *2767*3855# (works only on older versions)
Memory reset CUSTOM: *2767*2878# (works only on older versions)
Change dispplay contrast: * # 0 5 2 3 #
Memory info: * # 0 3 7 7 # or * # 0 2 4 6 #
Battery status: * # 9 9 9 8 * 2 2 8 #
Change sound of alarm: *#9998*289#
Vibra test: *#9998*842#
SIEMENS
S6, S8:
If you add to phonebook under 'own phone number' +12022243121 with namez (for example MMI), then you will see something
S10, E10:
In phonebook enter +12022243121 as your own phone no. You will see a picture with sun, two palms and greetings.
S15e:
Monitor Mode:
Code: *#7436267*8378# (*#SIEMENS*TEST#)
Hold red phone button until it code disapears.
Menu 3.3.4 Choose frequency.
Menu 3.3.4.1 Automaticaly.
Menu 3.3.4.2 Choose GSM-900
Menu 3.3.4.3 Choose GSM-1800
S25:
Enhanced Full Rate
*#3370# turns on
#3370# turns off
Haft Rate Mode
*#4720# turns on
#4720# turns off.
Languages:
*#0000#+green phone - choose automaticaly
*#0001#+green phone - English
*#0030#+green phone - Greek
*#0031#+green phone - Netherlands
*#0032#+green phone - French
*#0034#+green phone - Spanish
*#0039#+green phone - Italian
*#0049#+green phone - German
*#0090#+green phone - Turkish
How to change PIN2?
**04*old PIN2*new PIN2*new PIN2#
What is my software version?
Menu 8-8-2 press left-softkey when you see IMEI number, or *#06# and then green phone button and then press left soft-key.
How to extend battery life:
IrDA - turn on only when you need.
Turn off automatic network search (6-3)Turn off Vibration alarm.
C25:
Languages:
*#0000#+green phone - choose automaticaly
*#0001#+green phone - English
*#0030#+green phone - Greek
*#0031#+green phone - Netherlands
*#0032#+green phone - French
*#0034#+green phone - Spanish
*#0039#+green phone - Italian
*#0049#+green phone - German
*#0090#+green phone - Turkish
How to change PIN:
**04*old PIN*new PIN*new PIN#
How to check simlock status
*#0606# and then press left soft-key, you will see strange characters, then text ("brak blokad"). If you see for example 260-02, it means the phone is locked to Era GSM. In older models you can use *#06# and see the same information after clickin on left key (you will see IMEI and software version).
Alcatel
Numer IMEI: * # 0 6 #
Wersja oprogramowania: * # 0 6 #
Net Monitor: 0 0 0 0 0 0 *
Alcatel One Touch Easy Secrets
Codes :
Press *#06# to view IMEI number
Press *#000000# to enter Service Menu
To view Secret Menu type 000000 then press *
Bosch
Numer IMEI: * # 0 6 #
Ustawienia poczatkowe: * # 0 0 0 0 #
Net Monitor: * # 3 2 6 2 2 5 5 * 8 3 7 8 #
Reset telefonu: # 3 3 7 0#
Bosch 738 and Bosch 718, Bosch COM 607 and 908 Secrets
Codes:
*#06# to display the IMEI
*#0000# to set the language automaticaly (To english)
*#3370# to set the Enhaced Full Rate
#3370# to Reset the phone
*#9000# to enter sim lock code
*#9003# to enter the network code
*#9004# to enter the subset code
*#9100# to remove the sim lock permanently
*#9101# to remove the corporate lock permanently
*#9102# to remove the provider lock permanently
*#9103# to remove the network lock permanently
*#9104# to remove the subset lock permanently
Reveal Engineering Menu
Press *#3262255*8378# (equivalent to *#DANCALL*TEST#) to make secret Engineering
Dancall
Numer IMEI: * # 0 6 #
Wersja oprogramowania: * # 9 9 9 9 #
Ericsson 6xx/7xx/8xx
Numer IMEI: * # 0 6 #
Wersja oprogramowania: > * < < * < *
NOKIA 3110
Numer IMEI: * # 0 6 #
Wersja oprogramowania: * # 0 0 0 0 # lub *#9999#
Przywraca ustawienia fabryczne: *#7780#
Info o simlocku (specjalne menu) : * # 9 2 7 0 2 6 8 9 # (*#war0anty# )
lub *#3110#
Zatrzymanie zegara karty SIM *#746025625#
Philips
Numer IMEI: * # 0 6 #
Info o simlock`u: * # 8 3 7 7 #
Security code: * # 1 2 3 4 # (Fizz) albo * # 7 4 8 9 #
Philips DIGA phones:
Blocking list *#3333*#
Time connected *#2558*#
Flags,something *#3377*#
Security code *#7489*#
Philips FIZZ phones:
IMEI code *#06#
SW info *#8377*#
Security code *#1234*#
Philips SPARK phones:
IMEI: *#06#
Philips GENIE phones:
*#06# IMEI number
*#2254*# Status register: C, BS, RR, MMI, CREAT.
*#2255*# activate and deactivate the "DEBUG CALL"-Mode; when activated, make a
call to a busy line an the phone will display some
hex-codes on the display
*#2558*# the time in days,hours and minutes you are connected to the net
*#2562*# not clear; the phone reconnects to the net
*#2565*# not clear; warmstart
*#3333*# (NO) BLOCKING - list (15 items)
*#2377*# "BEER": not clear, the phone waits a random time and reconnects to the
net
*#3377*# Init, Flags, SIM LCK
*#3353*# resets the (NO) BLOCKING - list
*#7378*# Name, Length, SIM phase
*#7489*# SECURITY CODE
*#7693*# activate and deactivate the SLEEP MODE (when deactivated the battery
will go down!)
*#7787*# SPURIOUS INTERRUPT
*#7948*# SWITCH OFF
*#8463*# Some information about the SLEEP MODE: Wake, Sleep Req., Sleep
SAMSUNG SGH-600 SECRET CODES
============================
*#06# -> Show IMEI
*#9999# -> Show Software Version
*#0001# -> Show Serial Parameters
*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!!!! but also
change IMEI to 447967-89-400044-0, you must use CHGIMEI to
restore it)
*2767*2878# -> Custom EEEPROM Reset
*#9998*228# -> Battery status (capacity, voltage, temperature)
*#9998*246# -> Program status
*#9998*289# -> Change Alarm Buzzer Frequency
*#9998*324# -> Debug screens
*#9998*364# -> Watchdog
*#9998*377# -> EEPROM Error Stack
*#9998*427# -> Trace Watchdog
*#9998*523# -> Change LCD contrast
*#9998*544# -> Jig detect
*#9998*636# -> Memory status
*#9998*746# -> SIM File Size
*#9998*778# -> SIM Service Table
*#9998*785# -> RTK (Run Time Kernel) errors
*#9998*786# -> Run, Last UP, Last DOWN
*#9998*837# -> Software Version
*#9998*842# -> Test Vibrator
*#9998*862# -> Vocoder Reg
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal Error
*#9998*999# -> Last/Chk
*#9998*9266# -> Yann debug screen (=Debug Screens?)
*#9998*9999# -> Software version
*0001*s*f*t# -> Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# -> unknown
*0003*?# -> unknown
All CDMA codes...................
Here i post many codes for cdma phones ..............................
Samsung sph-n240, n400, a460, a500, etc Nam Programming:
Nam Set: ##Spc
Test Mode: 47*869#1235
Debug Menu: ##33284,ok
Service Menu: Menu+8+0 (#889)
Reset (Life time, Clear Memory, etc): ##786,ok
A-key: ##2539,ok
Label Selection: ##3882,ok
Label(Home, Work, etc) : **523,ok
NGG Setting (Gateway, etc.): ##2769737,ok
Vocoder: ##8626337,ok
CAI Change: ##7738,ok
Enable TTY: ##889,ok
Samsung sch-411, 611, n105, a100, a300, a2000, etc Nam Programming:
Nam Set: 47*869#08#9
Nam Set: Menu+60
Test Mode: *759#813580
Test Mode: 5809540*45680
A-key: Menu+0, 25##
External Audio: Menu+0, ####
Debug Menu: Menu+8, 0415 or Spc
Debug Menu: Menu+9, 0415 or Spc
Brief NAM Programing: Menu+40,626 (not all version)
LCD Contrast: Menu+45 (not all version)
SIO Mode: Menu+49
SIO Mode: Menu+69
Samsung a300, a530, a610, a620, a660, a670, etc Nam Programming:
Nam Set: Menu, 6, *
Service Menu: Menu, 9, *
Test Mode: 47*68#13580
Samsung X, E, V, S-series (korean), e250, v420, s250, etc Nam Programming:
Nam Set: 6548#0**4#6
Nam Set: 47*869#08#9
Nam Set: 74153697193
Test Mode: 5809540*45680 (88 - efs clear)
Debug Menu: Menu(hold 2sec)+0, 6725 or 9720 or 1973 or 0415
Debug Menu: Menu+0(hold 2sec), 6725 or 9720 or 1973 or 0415
Samsung N356 (India version) Nam Programming:
Test Mode: Menu, 5, down arrow, *
Test Mode: **00## (in some flashes)
Samsung i700, etc Nam Programming:
Nam Set: Go to start and select "PHONE" from the drop down menu, dial #83587
Samsung i300, etc Nam Programming:
1. Tap on the Phone Icon with stylus
2. Press #907*9#0 ENTER LOCK should appear on screen
3. Enter OTKSL
4. SVC MENU will appear press 1
5. Enter 10 digit MIN and then press SAVE
6. Press SAVE again
7. Press 3 and then press SAVE 6 times
8. Enter the HOME SID and press SAVE once
9. Press END key twice
TEST MODE COMMANDS:
n105_test_mode.txt
a500_test_mode.txt
a530_test_mode.txt
<>
Qualcomm qcp-800 Nam Pogramming:
Nam Set: Menu+3+0+Spc
Field Test: Menu+7+0+Fsc
Kyocera 1135, 2255, 3035, 5135, 6035, Se47, etc Nam Programming:
Nam Set: 111111+Jog Dial(Ok), Select "Programming"+Spc
CAI Change: ##7738,ok
Enable TTY: ##889,ok
Life Timer, PRL, etc: ##786,ok
A-key: ##2539,ok
A-key: 2539,ok
Tips:
On some kyocera handsets the factory service module has not been disabled
and the phone can be programmed without the spc by inputting.
Nam Set: ##333333 menu (service)
Hibrida GSM Sedang Offline Penilaian Reputasi Hibrida GSM Reply With Quote
SANYO>>
Sanyo 4900, 5150, 5300, 8100, etc Nam Programming:
Nam Set: ##Spc+Ok+Key Down+Ok
Advanced Setup: ##3282+Ok+Key Down+Ok+Msl
A-key: ##2539+Ok+Key Down+Ok
Version: ##**837+Ok+Key Down+Ok
Debug Menu: ##FSC+Ok+Key Down+Ok
Airtime menu: ##8463+Ok+Key Down+Ok
Change CAI: ##7738+Ok+Key Down+Ok
Vocoder: ##8626337+Ok+Key Down+Ok
Reverse Logistic: ##786+Ok+Key Down+Ok
Set IP Address: ##2769737+Ok+Key Down+Ok
TTY On/Off: ##889+Ok+Key Down+Ok
Ready Link: ##4636+Ok+Key Down+Ok
Browser Init On/Off: ##4682+Ok+Key Down+Ok
Picture Token: ##25327+Ok+Key Down+Ok
Unknown Code: ##5282277+Ok+Key Down+Ok
(SPC=000000, FSC=040793)
Sanyo scp-A011, smp-A017, etc Nam Programming:
Nam Set: F9(3 beep) + 0*72696#767
<>
Nokia 3280, 3285, 3580, 3585, 5185, 6185, 8280, etc Nam Programming:
Nam Set: *3001#12345#
Software Version: *#837#
Software Version: *#9999#
Esn Number: *#92772689#
Restart Phone: *#75681#
Restart Phone: *#75682#
Nokia 8887 Nam Programming:
Nam Set: *3001#12345#
Version: *#0000#
Evrc: *#8378#
Esn/Data/Timer: *#92772689#
SID: *#743#
ERICSSON
*#06# IMEI number
*#0000# or <> Restore English menu version
> * < < * < * Version of software
< * * < Simlock info
SAMSUNG
IMEI number: * # 0 6 #
Software version: * # 9 9 9 9 # or * # 0 8 3 7 #
Net Monitor: * # 0 3 2 4 #
Memory reset (removes SIMLOCK!!!): *2767*3855# (works only on older versions)
Memory reset CUSTOM: *2767*2878# (works only on older versions)
Change dispplay contrast: * # 0 5 2 3 #
Memory info: * # 0 3 7 7 # or * # 0 2 4 6 #
Battery status: * # 9 9 9 8 * 2 2 8 #
Change sound of alarm: *#9998*289#
Vibra test: *#9998*842#
SIEMENS
S6, S8:
If you add to phonebook under 'own phone number' +12022243121 with namez (for example MMI), then you will see something
S10, E10:
In phonebook enter +12022243121 as your own phone no. You will see a picture with sun, two palms and greetings.
S15e:
Monitor Mode:
Code: *#7436267*8378# (*#SIEMENS*TEST#)
Hold red phone button until it code disapears.
Menu 3.3.4 Choose frequency.
Menu 3.3.4.1 Automaticaly.
Menu 3.3.4.2 Choose GSM-900
Menu 3.3.4.3 Choose GSM-1800
S25:
Enhanced Full Rate
*#3370# turns on
#3370# turns off
Haft Rate Mode
*#4720# turns on
#4720# turns off.
Languages:
*#0000#+green phone - choose automaticaly
*#0001#+green phone - English
*#0030#+green phone - Greek
*#0031#+green phone - Netherlands
*#0032#+green phone - French
*#0034#+green phone - Spanish
*#0039#+green phone - Italian
*#0049#+green phone - German
*#0090#+green phone - Turkish
How to change PIN2?
**04*old PIN2*new PIN2*new PIN2#
What is my software version?
Menu 8-8-2 press left-softkey when you see IMEI number, or *#06# and then green phone button and then press left soft-key.
How to extend battery life:
IrDA - turn on only when you need.
Turn off automatic network search (6-3)Turn off Vibration alarm.
C25:
Languages:
*#0000#+green phone - choose automaticaly
*#0001#+green phone - English
*#0030#+green phone - Greek
*#0031#+green phone - Netherlands
*#0032#+green phone - French
*#0034#+green phone - Spanish
*#0039#+green phone - Italian
*#0049#+green phone - German
*#0090#+green phone - Turkish
How to change PIN:
**04*old PIN*new PIN*new PIN#
How to check simlock status
*#0606# and then press left soft-key, you will see strange characters, then text ("brak blokad"). If you see for example 260-02, it means the phone is locked to Era GSM. In older models you can use *#06# and see the same information after clickin on left key (you will see IMEI and software version).
Alcatel
Numer IMEI: * # 0 6 #
Wersja oprogramowania: * # 0 6 #
Net Monitor: 0 0 0 0 0 0 *
Alcatel One Touch Easy Secrets
Codes :
Press *#06# to view IMEI number
Press *#000000# to enter Service Menu
To view Secret Menu type 000000 then press *
Bosch
Numer IMEI: * # 0 6 #
Ustawienia poczatkowe: * # 0 0 0 0 #
Net Monitor: * # 3 2 6 2 2 5 5 * 8 3 7 8 #
Reset telefonu: # 3 3 7 0#
Bosch 738 and Bosch 718, Bosch COM 607 and 908 Secrets
Codes:
*#06# to display the IMEI
*#0000# to set the language automaticaly (To english)
*#3370# to set the Enhaced Full Rate
#3370# to Reset the phone
*#9000# to enter sim lock code
*#9003# to enter the network code
*#9004# to enter the subset code
*#9100# to remove the sim lock permanently
*#9101# to remove the corporate lock permanently
*#9102# to remove the provider lock permanently
*#9103# to remove the network lock permanently
*#9104# to remove the subset lock permanently
Reveal Engineering Menu
Press *#3262255*8378# (equivalent to *#DANCALL*TEST#) to make secret Engineering
Dancall
Numer IMEI: * # 0 6 #
Wersja oprogramowania: * # 9 9 9 9 #
Ericsson 6xx/7xx/8xx
Numer IMEI: * # 0 6 #
Wersja oprogramowania: > * < < * < *
NOKIA 3110
Numer IMEI: * # 0 6 #
Wersja oprogramowania: * # 0 0 0 0 # lub *#9999#
Przywraca ustawienia fabryczne: *#7780#
Info o simlocku (specjalne menu) : * # 9 2 7 0 2 6 8 9 # (*#war0anty# )
lub *#3110#
Zatrzymanie zegara karty SIM *#746025625#
Philips
Numer IMEI: * # 0 6 #
Info o simlock`u: * # 8 3 7 7 #
Security code: * # 1 2 3 4 # (Fizz) albo * # 7 4 8 9 #
Philips DIGA phones:
Blocking list *#3333*#
Time connected *#2558*#
Flags,something *#3377*#
Security code *#7489*#
Philips FIZZ phones:
IMEI code *#06#
SW info *#8377*#
Security code *#1234*#
Philips SPARK phones:
IMEI: *#06#
Philips GENIE phones:
*#06# IMEI number
*#2254*# Status register: C, BS, RR, MMI, CREAT.
*#2255*# activate and deactivate the "DEBUG CALL"-Mode; when activated, make a
call to a busy line an the phone will display some
hex-codes on the display
*#2558*# the time in days,hours and minutes you are connected to the net
*#2562*# not clear; the phone reconnects to the net
*#2565*# not clear; warmstart
*#3333*# (NO) BLOCKING - list (15 items)
*#2377*# "BEER": not clear, the phone waits a random time and reconnects to the
net
*#3377*# Init, Flags, SIM LCK
*#3353*# resets the (NO) BLOCKING - list
*#7378*# Name, Length, SIM phase
*#7489*# SECURITY CODE
*#7693*# activate and deactivate the SLEEP MODE (when deactivated the battery
will go down!)
*#7787*# SPURIOUS INTERRUPT
*#7948*# SWITCH OFF
*#8463*# Some information about the SLEEP MODE: Wake, Sleep Req., Sleep
SAMSUNG SGH-600 SECRET CODES
============================
*#06# -> Show IMEI
*#9999# -> Show Software Version
*#0001# -> Show Serial Parameters
*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!!!! but also
change IMEI to 447967-89-400044-0, you must use CHGIMEI to
restore it)
*2767*2878# -> Custom EEEPROM Reset
*#9998*228# -> Battery status (capacity, voltage, temperature)
*#9998*246# -> Program status
*#9998*289# -> Change Alarm Buzzer Frequency
*#9998*324# -> Debug screens
*#9998*364# -> Watchdog
*#9998*377# -> EEPROM Error Stack
*#9998*427# -> Trace Watchdog
*#9998*523# -> Change LCD contrast
*#9998*544# -> Jig detect
*#9998*636# -> Memory status
*#9998*746# -> SIM File Size
*#9998*778# -> SIM Service Table
*#9998*785# -> RTK (Run Time Kernel) errors
*#9998*786# -> Run, Last UP, Last DOWN
*#9998*837# -> Software Version
*#9998*842# -> Test Vibrator
*#9998*862# -> Vocoder Reg
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal Error
*#9998*999# -> Last/Chk
*#9998*9266# -> Yann debug screen (=Debug Screens?)
*#9998*9999# -> Software version
*0001*s*f*t# -> Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# -> unknown
*0003*?# -> unknown
All CDMA codes...................
Here i post many codes for cdma phones ..............................
Samsung sph-n240, n400, a460, a500, etc Nam Programming:
Nam Set: ##Spc
Test Mode: 47*869#1235
Debug Menu: ##33284,ok
Service Menu: Menu+8+0 (#889)
Reset (Life time, Clear Memory, etc): ##786,ok
A-key: ##2539,ok
Label Selection: ##3882,ok
Label(Home, Work, etc) : **523,ok
NGG Setting (Gateway, etc.): ##2769737,ok
Vocoder: ##8626337,ok
CAI Change: ##7738,ok
Enable TTY: ##889,ok
Samsung sch-411, 611, n105, a100, a300, a2000, etc Nam Programming:
Nam Set: 47*869#08#9
Nam Set: Menu+60
Test Mode: *759#813580
Test Mode: 5809540*45680
A-key: Menu+0, 25##
External Audio: Menu+0, ####
Debug Menu: Menu+8, 0415 or Spc
Debug Menu: Menu+9, 0415 or Spc
Brief NAM Programing: Menu+40,626 (not all version)
LCD Contrast: Menu+45 (not all version)
SIO Mode: Menu+49
SIO Mode: Menu+69
Samsung a300, a530, a610, a620, a660, a670, etc Nam Programming:
Nam Set: Menu, 6, *
Service Menu: Menu, 9, *
Test Mode: 47*68#13580
Samsung X, E, V, S-series (korean), e250, v420, s250, etc Nam Programming:
Nam Set: 6548#0**4#6
Nam Set: 47*869#08#9
Nam Set: 74153697193
Test Mode: 5809540*45680 (88 - efs clear)
Debug Menu: Menu(hold 2sec)+0, 6725 or 9720 or 1973 or 0415
Debug Menu: Menu+0(hold 2sec), 6725 or 9720 or 1973 or 0415
Samsung N356 (India version) Nam Programming:
Test Mode: Menu, 5, down arrow, *
Test Mode: **00## (in some flashes)
Samsung i700, etc Nam Programming:
Nam Set: Go to start and select "PHONE" from the drop down menu, dial #83587
Samsung i300, etc Nam Programming:
1. Tap on the Phone Icon with stylus
2. Press #907*9#0 ENTER LOCK should appear on screen
3. Enter OTKSL
4. SVC MENU will appear press 1
5. Enter 10 digit MIN and then press SAVE
6. Press SAVE again
7. Press 3 and then press SAVE 6 times
8. Enter the HOME SID and press SAVE once
9. Press END key twice
TEST MODE COMMANDS:
n105_test_mode.txt
a500_test_mode.txt
a530_test_mode.txt
<
Qualcomm qcp-800 Nam Pogramming:
Nam Set: Menu+3+0+Spc
Field Test: Menu+7+0+Fsc
Kyocera 1135, 2255, 3035, 5135, 6035, Se47, etc Nam Programming:
Nam Set: 111111+Jog Dial(Ok), Select "Programming"+Spc
CAI Change: ##7738,ok
Enable TTY: ##889,ok
Life Timer, PRL, etc: ##786,ok
A-key: ##2539,ok
A-key: 2539,ok
Tips:
On some kyocera handsets the factory service module has not been disabled
and the phone can be programmed without the spc by inputting.
Nam Set: ##333333 menu (service)
Hibrida GSM Sedang Offline Penilaian Reputasi Hibrida GSM Reply With Quote
SANYO>>
Sanyo 4900, 5150, 5300, 8100, etc Nam Programming:
Nam Set: ##Spc+Ok+Key Down+Ok
Advanced Setup: ##3282+Ok+Key Down+Ok+Msl
A-key: ##2539+Ok+Key Down+Ok
Version: ##**837+Ok+Key Down+Ok
Debug Menu: ##FSC+Ok+Key Down+Ok
Airtime menu: ##8463+Ok+Key Down+Ok
Change CAI: ##7738+Ok+Key Down+Ok
Vocoder: ##8626337+Ok+Key Down+Ok
Reverse Logistic: ##786+Ok+Key Down+Ok
Set IP Address: ##2769737+Ok+Key Down+Ok
TTY On/Off: ##889+Ok+Key Down+Ok
Ready Link: ##4636+Ok+Key Down+Ok
Browser Init On/Off: ##4682+Ok+Key Down+Ok
Picture Token: ##25327+Ok+Key Down+Ok
Unknown Code: ##5282277+Ok+Key Down+Ok
(SPC=000000, FSC=040793)
Sanyo scp-A011, smp-A017, etc Nam Programming:
Nam Set: F9(3 beep) + 0*72696#767
<
Nokia 3280, 3285, 3580, 3585, 5185, 6185, 8280, etc Nam Programming:
Nam Set: *3001#12345#
Software Version: *#837#
Software Version: *#9999#
Esn Number: *#92772689#
Restart Phone: *#75681#
Restart Phone: *#75682#
Nokia 8887 Nam Programming:
Nam Set: *3001#12345#
Version: *#0000#
Evrc: *#8378#
Esn/Data/Timer: *#92772689#
SID: *#743#
Langganan:
Postingan (Atom)
